South African Class 15C 4-8-2

South African Class 15C (15CB) 4-8-2

Class 15C Big Bill, as delivered, c. 1925
Type and origin
♠ With 57 inch (1,448 mm) coupled wheels
With 60 inch (1,524 mm) coupled wheels
Copper firebox - Steel firebox - ʘ Reboilered
ʘ 23x28 Cylinders - ʘ 24x28 Cylinders
Power type Steam
Designer Baldwin Locomotive Works
Builder Baldwin Locomotive Works
Serial number 58307, 58308, 58708-58717
Model Class 15C
Build date 1925-1926
Total produced 12
Specifications
Configuration 4-8-2 (Mountain)
Driver 2nd coupled axle
Gauge 3 ft 6 in (1,067 mm) Cape gauge
Leading dia. 30 in (762 mm)
Coupled dia. ♠ 57 in (1,448 mm)
60 in (1,524 mm)
Trailing dia. 33 in (838 mm)
Tender wheels 34 in (864 mm)
Wheelbase 65 ft 3 14 in (19,895 mm)
  Engine 35 ft 8 in (10,871 mm)
  Leading 6 ft 10 in (2,083 mm)
  Coupled 15 ft 9 in (4,801 mm)
  Tender 20 ft 5 in (6,223 mm)
  Tender bogie 6 ft 2 in (1,880 mm)
Length:
  Over couplers 73 ft 2 14 in (22,308 mm)
Height ♠ 12 ft 10 in (3,912 mm)
12 ft 11 12 in (3,950 mm)
Frame type Bar
Axle load 17 LT 13 cwt (17,930 kg)
17 LT 2 cwt (17,370 kg)
17 LT 19 cwt (18,240 kg)
17 LT 8 cwt (17,680 kg)
  Leading 18 LT 3 cwt (18,440 kg)
19 LT 5 cwt (19,560 kg)
18 LT 3 cwt (18,440 kg)
19 LT 5 cwt (19,560 kg)
  1st coupled 17 LT 13 cwt (17,930 kg)
17 LT 1 cwt (17,320 kg)
17 LT 16 cwt (18,090 kg)
17 LT 4 cwt (17,480 kg)
  2nd coupled 17 LT 12 cwt (17,880 kg)
17 LT 2 cwt (17,370 kg)
17 LT 18 cwt (18,190 kg)
17 LT 8 cwt (17,680 kg)
  3rd coupled 17 LT 13 cwt (17,930 kg)
17 LT 2 cwt (17,370 kg)
17 LT 19 cwt (18,240 kg)
17 LT 8 cwt (17,680 kg)
  4th coupled 17 LT 9 cwt (17,730 kg)
16 LT 18 cwt (17,170 kg)
17 LT 15 cwt (18,030 kg)
17 LT 4 cwt (17,480 kg)
  Trailing 16 LT 6 cwt (16,560 kg)
15 LT 19 cwt (16,210 kg)
16 LT 6 cwt (16,560 kg)
15 LT 19 cwt (16,210 kg)
  Tender bogie Bogie 1: 33 LT 18 cwt (34,440 kg)
Bogie 2: 35 LT 10 cwt (36,070 kg)
  Tender axle 17 LT 15 cwt (18,030 kg)
Adhesive weight 70 LT 7 cwt (71,480 kg)
68 LT 3 cwt (69,240 kg)
71 LT 8 cwt (72,550 kg)
69 LT 4 cwt (70,310 kg)
Loco weight 104 LT 16 cwt (106,500 kg)
103 LT 7 cwt (105,000 kg)
105 LT 17 cwt (107,500 kg)
104 LT 8 cwt (106,100 kg)
Tender weight 69 LT 8 cwt (70,510 kg)
Total weight 174 LT 4 cwt (177,000 kg)
172 LT 15 cwt (175,500 kg)
175 LT 5 cwt (178,100 kg)
173 LT 16 cwt (176,600 kg)
Tender type KT (2-axle bogies)
Fuel type Coal
Fuel capacity 14 LT (14.2 t)
Water cap 6,000 imp gal (27,300 l)
Firebox type Round-top, combustion chamber
  Firegrate area 48 sq ft (4.5 m2)
Boiler:
  Pitch ♠ 8 ft 6 in (2,591 mm)
8 ft 7 12 in (2,629 mm)
  Diameter 6 ft 2 14 in (1,886 mm)
  Tube plates 20 ft 12 in (6,109 mm)
  Small tubes143: 2 14 in (57 mm)
ʘ 117: 2 14 in (57 mm)
  Large tubes30: 5 12 in (140 mm)
ʘ 34: 5 12 in (140 mm)
Boiler pressure ♠ 200 psi (1,379 kPa)
210 psi (1,448 kPa)
Safety valve Coale Pop
Heating surface ♠ 2,777 sq ft (258.0 m2)
ʘ 2,584 sq ft (240.1 m2)
  Tubes ♠ 2,554 sq ft (237.3 m2)
ʘ 2,361 sq ft (219.3 m2)
  Arch tubes 23 sq ft (2.1 m2)
  Firebox 200 sq ft (19 m2)
Superheater:
  Type Schmidt
  Heating area ♠ 716 sq ft (66.5 m2)
ʘ 670 sq ft (62 m2)
Cylinders Two
Cylinder size ʘ 23 in (584 mm) bore
ʘ 24 in (610 mm) bore
ʘʘ 28 in (711 mm) stroke
Valve gear Walschaerts
Valve type Piston
Couplers Bell link-and-pin
AAR knuckle (c. 1930s-1950s)
Performance figures
Power outputʘ 38,980 lbf (173.4 kN) @ 75%
ʘ 42,440 lbf (188.8 kN) @ 75%
ʘ 38,880 lbf (172.9 kN) @ 75%
ʘ 42,340 lbf (188.3 kN) @ 75%
Career
Operators South African Railways
Class Class 15C, 15CB
Number in class 12
Numbers 2060–2071
Nicknames Big Bill
Delivered 1925-1926
First run 1925
Withdrawn 1976
♠ The leading coupled axle had flangeless wheels

The South African Railways Class 15C 4-8-2 of 1925 was a steam locomotive.

In 1925, the South African Railways placed two American-built Class 15C steam locomotives with a 4-8-2 Mountain type wheel arrangement in service. Another ten locomotives were ordered and delivered a year later. In 1926, these locomotives were reclassified to Class 15CB.[1][2][3]

Manufacturer

On 15 December 1924, after an official tour of investigation to the United States of America by G.E. Titren, the Superintendent Motive Power of the South African Railways (SAR), an order was placed with the Baldwin Locomotive Works (BLW) of Philadelphia for four experimental locomotives, two of which were of a 4-8-2 Mountain type wheel arrangement. These locomotives, both types specially designed for the long runs of the Union Limited and Union Express passenger trains between Cape Town and Johannesburg, were delivered in 1925.[1][2][3]

Characteristics

These locomotives conformed to SAR requirements as far as practicable, but also incorporated the latest American railway engineering practices. They introduced several features which were new to the SAR at the time, such as top feeds to the boiler, self-cleaning smokeboxes, Sellar's drifting valves and grease lubrication to the coupled wheel axleboxes, crank pins and connecting rod big ends. Their fireboxes were equipped with flexible side stays and water siphon arch tubes to support the brick arch and to improve circulation. Their Type KT tenders, arranged with self-trimming type coal bunkers, had a coal capacity of 14 long tons (14.2 tonnes) and a water capacity of 6,000 imperial gallons (27,300 litres), which was considered sufficient for the engines to travel 100 miles (161 kilometres) without having to replenish water.[1][2][3]

The locomotives represented a considerable advance in power over the Classes 15, 15A and 15B. They had 5 inches (127 millimetres) thick bar frames and their boilers were larger in proportions than that of any existing SAR locomotive, while their boiler pitch was raised 10 inches (254 millimetres) higher than that of anything else in service at that time. The boilers were equipped with three Coale pop type safety valves and a Schmidt type superheater. To reduce the length between boiler tube plates, a 2 feet 3 inches (686 millimetres) long combustion chamber was provided in the firebox. The locomotive's size quickly earned it the nickname Big Bill, while its contemporary Class 16D 4-6-2 Pacific type, which arrived from the same builders in the same shipment, was nicknamed Big Bertha.[2][3]

The first two locomotives, designated Class 15C with engine numbers 2060 and 2061, were erected at the Salt River shops and put to work on the line from Cape Town to Touws River. They performed well, were comparatively trouble-free, and were good steamers, capable of handling a heavy load exceeding that of any other locomotive which had been employed on this section to date.[1][2]

Because of the good results obtained from these two engines, an order was placed with Baldwin for another ten locomotives, which were delivered in 1926, numbered in the range from 2062 to 2071. All these locomotives were delivered new with copper fireboxes, but once sufficient water treatment facilities were available to prevent problems with corrosion, these were gradually replaced with steel fireboxes as and when firebox replacement became necessary.[1][2]

Reclassification

Shortly after being placed in service, the Class 15C's frames began to show evidence of cracking. A similar locomotive, which differed mainly in the design of the frame under the firebox, was then ordered from the American Locomotive Company (ALCO). When the 23 ALCO-built locomotives were placed in service in 1926, they were designated Class 15CA, with the "A" supposedly indicating the manufacturer ALCO rather than, as was usual SAR practice, a different version of an existing locomotive type.[3]

The Class 15C was then, rather unnecessarily, reclassified to Class 15CB, with the "B" merely to indicate the manufacturer Baldwin and not, as was usual practice, a branchline locomotive.[1][3]

Modifications

Retyring

They were delivered with 57 inches (1,450 millimetres) coupled wheels and their boiler safety valves were set at an operating pressure of 200 pounds per square inch (1,380 kilopascals). All twelve engines eventually had their coupled wheels retyred to 60 inches (1,520 millimetres) diameter and, to compensate for the loss of tractive effort due to the larger diameter wheels, their operating boiler pressure was increased to 210 pounds per square inch (1,450 kilopascals) by an adjustment of the setting of their safety valves. This modification enabled these mixed traffic locomotives to handle the fastest mainline passenger trains. Probably at the same time, their cylinders were reamed from a 23 to 24 inches (584 to 610 millimetres) bore.[1][2][4][5]

When larger tyres were fitted, the old tyres were left in position and turned down on the wheel centres to serve as liners, and the new tyres were then shrunk on over the liners. The practice of increasing the diameter of coupled wheels, wheel spacing and other considerations permitting, was begun by A.G. Watson during his term in office as Chief Mechanical Engineer (CME) and was continued by his successors. The reduction of tractive effort caused by the larger wheels, was made up by increasing boiler pressures or by fitting larger cylinders or both, as required. This policy resulted in more mileage between heavy repairs, less cost-per-mile on repairs and locomotives capable of higher speeds.[2]

Reboilering

Three of the Class 15CB and Class 15CA locomotives were reboilered during the early 1940s, with new boiler numbers in the range from 9504 to 9506. These boilers were of similar dimensions to the originals, but with a different tube arrangement, and were designed by Dr. M.M. Loubser, CME at the time. The reboilered locomotives were not reclassified.[4][5]

Service

South African Railways

The locomotives gave good service and were justifiably popular with traffic, running and engineering staff alike. The introduction of these large engines, along with their Class 16D 4-6-2 Pacific type Big Bertha siblings, resulted in a complete revision of traffic operation between Cape Town and Johannesburg. The Pacifics were scheduled to work the 616 miles (991 kilometres) stretch between Johannesburg and Beaufort West, while the Big Bill Mountains entered service on the 340 miles (547 kilometres) stretch from Beaufort West to Cape Town, with its ruling gradient of 1 in 40 (2½%) and severe curvature for approximately 22 miles (35 kilometres) on the Hex River Pass section between Touws River and De Doorns.[2][3]

They were later transferred to Bloemfontein, from where they worked south to Noupoort. A brief stint on the Natal north coast followed in the mid-1960s, after which they spent the rest of their SAR working lives in the Eastern and Western Transvaal. They were withdrawn from SAR service in 1976.[3]

Industrial

Eleven Class 15CB locomotives were sold into industrial service in 1976, with only the first-built, no. 2060, being retained by the SAR for preservation. By the late 1980s, therefore, at more than 60 years of age, eleven of the original twelve Class 15CB locomotives were still at work.[6]

Illustration

The main picture shows a Class 15C, as delivered, c. 1925, while the following show two Class 15CB locomotives in industrial service after withdrawal from SAR service.

References

  1. 1 2 3 4 5 6 7 Holland, D.F. (1972). Steam Locomotives of the South African Railways, Volume 2: 1910-1955 (1st ed.). Newton Abbott, Devon: David & Charles. pp. 46–49. ISBN 978-0-7153-5427-8.
  2. 1 2 3 4 5 6 7 8 9 Espitalier, T.J.; Day, W.A.J. (1946). The Locomotive in South Africa - A Brief History of Railway Development. Chapter VII - South African Railways (Continued). South African Railways and Harbours Magazine, May 1946. pp. 373-376.
  3. 1 2 3 4 5 6 7 8 Paxton, Leith; Bourne, David (1985). Locomotives of the South African Railways (1st ed.). Cape Town: Struik. pp. 10–11, 61–62, 66. ISBN 0869772112.
  4. 1 2 South African Railways & Harbours/Suid Afrikaanse Spoorweë en Hawens (15 Aug 1941). Locomotive Diagram Book/Lokomotiefdiagramboek, 3'6" Gauge/Spoorwydte. SAR/SAS Mechanical Department/Werktuigkundige Dept. Drawing Office/Tekenkantoor, Pretoria. pp. 19-20, 45-46.
  5. 1 2 South African Railways & Harbours/Suid Afrikaanse Spoorweë en Hawens (15 Aug 1941). Locomotive Diagram Book/Lokomotiefdiagramboek, 2'0" & 3'6" Gauge/Spoorwydte, Steam Locomotives/Stoomlokomotiewe. SAR/SAS Mechanical Department/Werktuigkundige Dept. Drawing Office/Tekenkantoor, Pretoria. pp. 6a-7a, 19-20, 45-46.
  6. Durrant, A E (1989). Twilight of South African Steam (1st ed.). Newton Abbott, London: David & Charles. p. 88. ISBN 0715386387.
Wikimedia Commons has media related to South African Class 15C (4-8-2).
This article is issued from Wikipedia - version of the 5/22/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.