South African Class MG 2-6-6-2

CSAR Mallet 2-6-6-2 Stoker
South African Class MG 2-6-6-2

SAR no. 1628, ex CSAR no. 1024, c. 1912
Type and origin
Power type Steam
Designer American Locomotive Company
Central South African Railways
(G.G. Elliot)
Builder American Locomotive Company
Serial number 49124
Model CSAR Mallet
Build date 1911
Total produced 1
Specifications
Configuration 2-6-6-2 (Prairie Mallet)
Driver 3rd & 6th coupled axles
Gauge 3 ft 6 in (1,067 mm) Cape gauge
Leading dia. 28 12 in (724 mm)
Coupled dia. 51 in (1,295 mm) front unit
46 in (1,168 mm) rear unit
Trailing dia. 28 12 in (724 mm)
Tender wheels 34 in (864 mm)
Wheelbase 66 ft 9 in (20,345 mm)
  Engine 41 ft 6 in (12,649 mm)
  Coupled 9 ft 2 in (2,794 mm) front unit
8 ft 4 in (2,540 mm) rear unit
  Tender 17 ft 11 in (5,461 mm)
  Tender bogie 4 ft 7 in (1,397 mm)
Length:
  Over couplers 74 ft 10 14 in (22,816 mm)
Height 12 ft 10 78 in (3,934 mm)
Frame type Bar
Axle load 15 LT 3 cwt 2 qtr (15.42 t)
  Leading 7 LT 11 cwt 2 qtr (7.697 t)
  1st coupled 14 LT 6 cwt (14.53 t)
  2nd coupled 14 LT 14 cwt 2 qtr (14.96 t)
  3rd coupled 14 LT 14 cwt 2 qtr (14.96 t)
  4th coupled 14 LT 14 cwt 2 qtr (14.96 t)
  5th coupled 14 LT 14 cwt 2 qtr (14.96 t)
  6th coupled 15 LT 3 cwt 2 qtr (15.42 t)
  Tender bogie 25 LT 8 cwt 2 qtr (25,830 kg) each
  Tender axle 12 LT 14 cwt 1 qtr (12,920 kg) av.
Adhesive weight 88 LT 7 cwt 2 qtr (89.79 t)
Loco weight 103 LT 2 cwt (104.8 t)
Tender weight 50 LT 17 cwt (51.67 t)
Total weight 153 LT 19 cwt (156.4 t)
Tender type 2-axle bogies
Fuel type Coal
Fuel capacity 10 LT (10.2 t)
Water cap 4,000 imp gal (18,200 l)
Firebox type Round-top
  Firegrate area 49.5 sq ft (4.60 m2)
Boiler:
  Pitch 7 ft 11 12 in (2,426 mm)
  Diameter 6 ft 18 in (1,832 mm)
  Tube plates 20 ft 4 18 in (6,201 mm)
  Small tubes 269 2 14 in (57 mm)
Boiler pressure 200 psi (1,379 kPa)
Safety valve Ramsbottom
Heating surface 3,383.5 sq ft (314.34 m2)
  Tubes 3,223 sq ft (299.4 m2)
  Firebox 160.5 sq ft (14.91 m2)
Cylinders Four
High-pressure cylinder 18 in (457 mm) bore
26 in (660 mm) stroke
Low-pressure cylinder 28 12 in (724 mm) bore
28 in (711 mm) stroke
Valve gear Walschaerts
Couplers Bell link-and-pin
Performance figures
Tractive effort 45,200 lbf (201 kN) @ 50%
Career
Operators Central South African Railways
South African Railways
Class Class MG
Number in class 1
Numbers CSAR 1024, SAR 1628
Delivered 1911
First run 1911
Withdrawn 1927

The South African Railways Class MG 2-6-6-2 of 1911 was a steam locomotive from the pre-Union era in the Transvaal.

In 1911, the Central South African Railways placed an experimental Mallet articulated compound steam locomotive with a 2-6-6-2 wheel arrangement in service. In 1912, when it was assimilated into the South African Railways, it was renumbered and designated the sole Class MG.[1][2][3][4]

Manufacturer

G.G. Elliot

A single experimental locomotive was included with the order for nine Class MF Mallet articulated compound steam locomotives which were delivered to the Central South African Railways (CSAR) by the American Locomotive Company (ALCO) in 1911.[1][2][3][4]

It was similar to the other nine engines, but used saturated instead of superheated steam, had a mechanical stoker and the coupled wheels on the leading engine unit were of a 5 inches (127 millimetres) larger diameter than those of the trailing engine unit. It had Walschaerts valve gear and was numbered 1024.[1][2][3][4]

Compound expansion

In a compound locomotive, steam is expanded in phases. After being expanded in a high-pressure cylinder and having then lost pressure and given up part of its heat, it is exhausted into a larger-volume low-pressure cylinder for secondary expansion, after which it is exhausted through the smokebox. By comparison, in the more usual arrangement of simple expansion (simplex), steam is expanded just once in any one cylinder before being exhausted through the smokebox.[1][5]

In the compound Mallet locomotive, the rear set of coupled wheels are driven by the smaller high-pressure cylinders, which are fed steam from the steam dome. Their spent steam is then fed to the larger low-pressure cylinders, which drive the front set of coupled wheels.[1][3]

Characteristics

Apart from having a different boiler, there were three major differences between this locomotive and the nine Class MF engines, which were built and delivered at the same time.[3]

Saturated steam

It was not equipped with a superheater, although superheated locomotives had already been proven to be more economic and superior in performance.[1][2][3]

Coupled wheels

The front set of coupled wheels was of a larger diameter than the rear set. In theory, this configuration was to result in improved acceleration, with the rear engine unit providing the traction. It was also believed that the difference in frequency between the front and rear cylinder exhaust beats would result in a more even pressure in the receiver pipe and therefore improved steam flow, although exactly how this was to come about was not clear. It was the only South African articulated locomotive to have coupled wheels of different diameters.[1][2][3]

Owing to the larger diameter wheels of the rear engine unit, the boiler pitch had to be raised to 7 feet 11 12 inches (2,426 millimetres), the highest pitched boiler in South Africa at the time.[2]

The unorthodox driving wheel configuration did not have the expected results and, in comparison with the other nine superheated engines, the locomotive proved to be inferior in performance.[1]

Mechanical stoker

This was the first South African locomotive to be equipped with a mechanical stoker. This device, of the Street type, consisted of a coal crusher, hand-fed by the fireman, which was fitted to the front left hand side of the tender footplate and driven by a small steam engine, which was mounted behind the hand brake column.[1][2][3]

The crusher reduced the coal to a suitable size for the stoker. The crushed coal then fell by gravity into a chute, which led to a receiving bin which was fitted below the back buffer beam of the locomotive, from where it was picked up by a bucket elevator which worked in a large pipe. The full buckets were carried up in the left-hand-side tube, mounted on the back of the firebox, were discharged into a central receiver and then travelled empty down the right hand side tube.[1][2]

The bucket belt was driven by another small steam engine, mounted on the left side of the firebox near the top. The main shaft of this engine had adjustable cams, which operated three steam cocks which supplied steam jets to the coal delivery orifices. From the central receiver, a cone-shaped tray directed the coal to the right, centre or left sides as required, while the cam-operated steam jets blew the coal into the firebox. When coal was only required at the back end of the firebox, the cams could be projected a short distance, thereby allowing steam jets of just sufficient power to project the coal to the required parts of the firebox.[1][2]

It was a very complicated, cumbersome and extremely noisy arrangement, which required the fireman to attend to two auxiliary engines and feed the crusher, in addition to his normal duties. The noise created by this mechanism was stated to be deafening to the crew and was threefold, first the noise of the crusher, then the noisy circulation of the conveyor buckets, and finally the sharp reports of the steam jets which controlled the feeding.[1][2][3]

The mechanical stoker was removed and the locomotive was converted to hand firing soon after being placed in service.[1][2][3]

Service

When the Union of South Africa was established on 31 May 1910, the three Colonial government railways (Cape Government Railways, Natal Government Railways and CSAR) were united under a single administration to control and administer the railways, ports and harbours of the Union. Although the South African Railways and Harbours came into existence in 1910, with Sir William Hoy appointed as its first General Manager, the actual classification and renumbering of all the rolling stock of the three constituent railways required careful planning and was only implemented with effect from 1 January 1912.[4][6]

In 1912, this locomotive was renumbered 1628 and classified as Class MG on the South African Railways (SAR). It joined the experimental Class MD and the Class MF on the coal traffic line between Witbank and Germiston, where it remained until it was withdrawn from service in 1927.[1][3][4]

Illustration

The main picture shows Class MG number 1628 in its original lined SAR livery. It was later repainted in the more well-known plain black SAR livery.

References

  1. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Holland, D.F. (1972). Steam Locomotives of the South African Railways, Volume 2: 1910-1955 (1st ed.). Newton Abbott, Devon: David & Charles. pp. 16–18, 140. ISBN 978-0-7153-5427-8.
  2. 1 2 3 4 5 6 7 8 9 10 11 Espitalier, T.J.; Day, W.A.J. (1945). The Locomotive in South Africa - A Brief History of Railway Development. Chapter VII - South African Railways. South African Railways and Harbours Magazine, April 1945. pp. 275-276.
  3. 1 2 3 4 5 6 7 8 9 10 11 Paxton, Leith; Bourne, David (1985). Locomotives of the South African Railways (1st ed.). Cape Town: Struik. p. 87. ISBN 0869772112.
  4. 1 2 3 4 5 Classification of S.A.R. Engines with Renumbering Lists, issued by the Chief Mechanical Engineer’s Office, Pretoria, January 1912, pp. 9, 12, 16, 47 (Reprinted in April 1987 by SATS Museum, R.3125-6/9/11-1000)
  5. Compounding Steam Engines
  6. The South African Railways - Historical Survey. Editor George Hart, Publisher Bill Hart, Sponsored by Dorbyl Ltd., Published c. 1978, p. 25.
Wikimedia Commons has media related to South African Class MG (2-6-6-2).
This article is issued from Wikipedia - version of the 11/21/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.