South African Class 6E1, Series 1

South African Class 6E1, Series 1

No. E1228 at Warrenton with a lime train, 24 August 2007
Type and origin
Power type Electric
Designer Union Carriage and Wagon
Builder Union Carriage and Wagon
Model UCW 6E1
Build date 1969-1970
Total produced 20
Specifications
AAR wheel arr. B-B
UIC class Bo'Bo'
Gauge 3 ft 6 in (1,067 mm) Cape gauge
Wheel diameter 1,220 mm (48.0 in)
Wheelbase 11,279 mm (37 ft 0.1 in)
  Bogie 3,430 mm (11 ft 3.0 in)
Pivot centres 7,849 mm (25 ft 9.0 in)
Panto shoes 6,972 mm (22 ft 10.5 in)
Length:
  Over couplers 15,494 mm (50 ft 10.0 in)
  Body 14,631 mm (48 ft 0 in)
Width 2,896 mm (9 ft 6.0 in)
Height:
  Pantograph 4,089 mm (13 ft 5.0 in)
  Body height 3,937 mm (12 ft 11.0 in)
Axle load 22,226 kg (49,000 lb)
Adhesive weight 88,904 kg (196,000 lb)
Loco weight 88,904 kg (196,000 lb)
Power supply Catenary
Current collection Pantographs
Traction motors Four AEI-283AZ
  Rating 1 hour 623 kW (835 hp)
  Continuous 563 kW (755 hp)
Gear ratio 18:67
Loco brake Air & Regenerative
Train brakes Air & Vacuum
Couplers AAR knuckle
Performance figures
Maximum speed 113 km/h (70 mph)
Power output:
  1 hour 2,492 kW (3,342 hp)
  Continuous 2,252 kW (3,020 hp)
Tractive effort:
  Starting 311 kN (70,000 lbf)
  1 hour 221 kN (50,000 lbf)
  Continuous 193 kN (43,000 lbf) @ 40 km/h (25 mph)
Career
Operators South African Railways
Spoornet
Transnet Freight Rail
Class Class 6E1
Power class 3 kV DC
Number in class 20
Numbers E1226-E1245
Delivered 1969-1970
First run 1969

The South African Railways Class 6E1, Series 1 of 1969 is an electric locomotive.

In 1969 and 1970, the South African Railways placed twenty Class 6E1, Series 1 electric locomotives with a Bo-Bo wheel arrangement in mainline service. Their limited number and the fact that they entered service before the Class 6E, suggest that the Class 6E1, Series 1 locomotives were obtained as demonstrators, before a decision was made on which of the two classes would be perpetuated.[1][2]

Manufacturer

The 3 kV DC Class 6E1, Series 1 electric locomotive was designed and built for the South African Railways (SAR) in 1969 and 1970 by Union Carriage and Wagon (UCW) in Nigel, Transvaal, with the electrical equipment supplied by Associated Electrical Industries (AEI) and English Electric (EE).[3][4]

Twenty locomotives were delivered in 1969 and 1970, numbered in the range from E1226 to E1245. UCW did not allocate builder’s or works numbers to the locomotives it built for the SAR and used the SAR unit numbers for their record keeping.[1]

Characteristics

Bogies

The twenty Series 1 locomotives are identical to the Class 6E in all respects, including traction motors, power, tractive force and body dimensions. The only obvious visual distinguishing feature to tell the Class 6E1, Series 1 apart, was its new design bogies with their distinctive traction struts and linkages.[1][5]

Class 6E1, Series 1 bogie
Bogie frame and wheels

Together with the locomotive's electronic wheelslip detection system, these traction struts, mounted between the linkages on the bogies and the locomotive body and colloquially referred to as grasshopper legs, ensure the maximum transfer of power to the rails without causing wheel-slip, by reducing the adhesion of the leading bogie and increasing that of the trailing bogie by as much as 15% upon starting off. This feature was controlled by electronic wheel-slip detection devices and an electric weight transfer relay, which reduced the anchor current to the leading bogie by as much as 50A in notches 2 to 16. These grasshopper legs and linkages were to become a distinguishing feature on the bogies of most subsequent South African electric locomotive classes.[5]

The limited number of Class 6E1, Series 1 locomotives which were placed in service and the fact that they entered service before the Class 6E, suggest that the Series 1 locomotives were obtained as demonstrators for these new bogies to be evaluated, before a decision was made about their continued production.[2]

Orientation

These dual cab locomotives have a roof access ladder on one side only, just to the right of the cab access door. The roof access ladder end is marked as the no. 2 end. A corridor along the centre of the locomotive connects the cabs, which are identical, apart from the fact that the handbrake is located in cab 2. A pantograph hook stick is stowed in a tube, mounted below the lower edge of the locomotive body on the roof access ladder side. The locomotive has three small panels along the lower half of the body on the roof access ladder side, and only one panel on the opposite side.[1]

Series identifying features

The Class 6E1 was produced in eleven series over a period of nearly sixteen years, with altogether 960 units placed in service, all built by UCW. This makes the Class 6E1 the most numerous single locomotive class ever to have seen service in South Africa and serves as ample proof of a highly successful design.[1][5]

While some Class 6E1 series are visually indistinguishable from their predecessors or successors, some externally visible changes did occur over the years. Like the Classes 5E, 5E1 and 6E, the Class 6E1, Series 1 locomotives had their sandboxes mounted on the bogies, while all the subsequent series Class 6E1s had their sandboxes mounted along the bottom edge of the locomotive body, with the sandbox lids fitting into recesses in the body.[1][5]

Operation

Startup

When there is no compressed air in the locomotive's system to raise a pantograph to start up, a pantograph hook stick is used to manually raise the pantograph. This starts the high voltage motor, which drives the auxiliary alternator to supply 110V power, to start the compressor and power other control circuits. Once there is enough main air pressure to keep the pantograph in the raised position, the pantograph hook stick can be dropped.[6]

The locomotive is controlled via resistors, over which the voltage is dropped in a configuration of series and parallel electrical circuits. The circuit breakers which switch these circuits, work under very high power and voltage and are therefore all pneumatically operated for insulation purposes. Compressed air is required to open or close the switch actions and air is also used for the weakfield cam switch, which also switches under very high currents.[6]

Running

Upon starting off and in the low notches, the major part of the voltage is dropped over the banks of resistors and all four traction motors are in series.[6] The blowers which, accelerate the dissipation of heat in the resistor banks, give the Class 6E its very distinctive sound, a deep and loud whine when power is applied.[2]

As the driver notches up, some of the resistor banks are cut out via the pneumatically operated switches and the voltage increases across the traction motors. The more resistors which are cut out as the driver notches higher, the more power is developed by the traction motors. At around 22 to 28 kilometres per hour (14 to 17 miles per hour) the locomotive switches to a parallel combination, where the two traction motors per bogie are in a series electrical circuit, while the two bogies are in parallel electrical circuit. Eventually, when all resistors are cut out, the locomotive is operating in full-field.[6]

When the traction motors are operated in full-field, be it in series or parallel mode, they are performing at maximum power for normal operation. To increase the speed at this point, if necessary, higher power output is required from the traction motors. The only way to increase power is to force a higher current flow. To accomplish this, the weakfield cam switch switches resistance in parallel with the field coils, which reduces the overall resistance of the field coils. This increases the magnetic flux and more power is generated by the traction motors, over short periods.[6]

Brakes

The locomotive itself used air brakes, but it was equipped to operate trains with air or vacuum brakes. The brake system would be set up for either air or vacuum train working by means of a turning switch on the driver's brake valve, and by pre-setting the appropriate brake valves in the passage.

Compressed air pipes

The Class 6E1 locomotives were built with an air brake system, consisting of various valves connected to each other with pipes, commonly referred to as a “bicycle frame” brake system. The compressed air pipes run under the locomotive's belly in a zig-zag pattern, going through bolster and other members to extend its length, to allow the maximum amount of moisture to condense on the way to the reservoirs. As a result, it has multiple pipe connections. A weakness of the system was that, after an accident or even a hard coupling, these pipes tended to develop leaks at the joints, which were extremely difficult to repair.[7]

While hauling a vacuum braked train, the locomotive's air brake system would be disabled and the train would be controlled by using the train brakes alone to slow down and stop. While hauling an air braked train, on the other hand, the locomotive brakes would engage along with the train brakes. While working either type of train downgrade, the locomotive's regenerative braking system would also work in conjunction with the train brakes.

Unlike the Classes 5E and 5E1, whose air brakes could be applied independently on each bogie when the locomotive was stopped, the air brakes on both bogies would be applied together on the Classes 6E and 6E1. The handbrake or parking brake, located in Cab no. 2, only operated on the unit's last axle, or no. 7 and 8 wheels.

Service

The Class 6E1 family saw service all over both of the 3 kV DC mainline and branchline networks.[3]

Cape Western network

The smaller network is the Cape Western line between Cape Town and Beaufort West, with the locomotives based at the Bellville Depot in Cape Town.[3]

Northern network

The larger network covers portions of the Northern Cape, the Free State, Natal, Gauteng, North West Province and Mpumalanga, the main routes in this vast area being as follows:[3]

The electric locomotives, allocated to depots within this network, are largely pooled and can operate anywhere in the network, as required by the Operating Department, but they return to their home depots for maintenance every twenty-eight days.[3]

In 2011, the Class 6E1 began to be withdrawn from the Natal corridor (NatCor) line between Johannesburg and Durban, and replaced with Class 18E locomotives.[3]

In KwaZulu-Natal, the coastal sections from Durban to Empangeni in the north and to Port Shepstone in the south were due to be dieselised at the end of October 2011, using EMD Classes 34 and 37-000 locomotives, which were being displaced by the introduction of new Class 43-000 diesel-electric locomotives on the line from Mpumalanga via Swaziland to Richards Bay.[8]

In practice, however, electric locomotives were observed at Port Shepstone as late as 24 May 2012, while the diesel power on the South Coast line consisted predomiminantly of Class 37-000 locomotives. The overhead catenary equipment between Stanger and Empangeni and between Kelso and Port Shepstone was to be removed soon after the end of October 2011, but actual removal only took place in November 2013. By October 2014, the catenary masts, sans wiring, were still standing at Port Shepstone.

Illustration

The Series 1 locomotives were all delivered in the SAR Gulf Red livery with yellow whiskers. By c. 2000, they were all repainted in the Spoornet orange livery.

References

  1. 1 2 3 4 5 6 South African Railways Index and Diagrams Electric and Diesel Locomotives, 610mm and 1065mm Gauges, Ref LXD 14/1/100/20, 28 January 1975, as amended
  2. 1 2 3 Dulez, Jean A. (2012). Railways of Southern Africa 150 Years (Commemorating One Hundred and Fifty Years of Railways on the Sub-Continent - Complete Motive Power Classifications and Famous Trains - 1860-2011) (1st ed.). Garden View, Johannesburg, South Africa: Vidrail Productions. p. 297. ISBN 9 780620 512282.
  3. 1 2 3 4 5 6 Middleton, John N. (2002). Railways of Southern Africa Locomotive Guide - 2002 (as amended by Combined Amendment List 4, January 2009) (2nd, Dec 2002 ed.). Herts, England: Beyer-Garratt Publications. pp. 49–51.
  4. "UCW - Electric locomotives" (PDF). The UCW Partnership. Archived from the original (PDF) on 12 October 2007. Retrieved 30 September 2010.
  5. 1 2 3 4 Paxton, Leith; Bourne, David (1985). Locomotives of the South African Railways (1st ed.). Cape Town: Struik. pp. 128–129. ISBN 0869772112.
  6. 1 2 3 4 5 Operation - South African Classes 6E, 6E1, 16E, 17E and 18E
  7. Information obtained from Transnet engineers and drivers
  8. Railways Africa, 18 Oct 2011: KwaZulu-Natal coastal region de-electrification
Wikimedia Commons has media related to South African Class 6E1 Series 1.
This article is issued from Wikipedia - version of the 9/13/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.