Orthogonal instruction set

In computer engineering, an orthogonal instruction set is an instruction set architecture where all instruction types can use all addressing modes. It is "orthogonal" in the sense that the instruction type and the addressing mode vary independently. An orthogonal instruction set does not impose a limitation that requires a certain instruction to use a specific register.[1]

Orthogonality in practice

In many CISC computers, an instruction could access either registers or memory, usually in several different ways. This made the CISC machines easier to program, because rather than being required to remember thousands of individual instruction opcodes, an orthogonal instruction set allowed a programmer to instead remember just thirty to a hundred operation codes ("ADD", "SUBTRACT", "MULTIPLY", "DIVIDE", etc.) and a set of three to ten addressing modes ("FROM REGISTER 0", "FROM REGISTER 1", "FROM MEMORY", etc.). The DEC PDP-11 and Motorola 68000 computer architectures are examples of nearly orthogonal instruction sets, while the ARM11 and VAX are examples of CPUs with fully orthogonal instruction sets.

The PDP-11

With the exception of its floating point instructions, the PDP-11 was very strongly orthogonal. Every integer instruction could operate on either 1-byte or 2-byte integers and could access data stored in registers, stored as part of the instruction, stored in memory, or stored in memory and pointed to by addresses in registers. Even the PC and the stack pointer could be affected by the ordinary instructions using all of the ordinary data modes. In fact, "immediate" mode (hardcoded numbers within an instruction, such as ADD #4, R1 (R1 = R1 + 4) was implemented as the mode "register indirect, autoincrement" and specifying the program counter (R7) as the register to use reference for indirection and to autoincrement.

Since the PDP-11 was an octal-oriented (3-bit sub-byte) machine (addressing modes 0–7, registers R0–R7), there were (electronically) 8 addressing modes. Through the use of the Stack Pointer (R6) and Program Counter (R7) as referenceable registers, there were 10 conceptual addressing modes available.

The VAX-11

The VAX-11 extended the PDP-11's orthogonality to all data types, including floating point numbers (although instructions such as 'ADD' were divided into data-size dependent variants such as ADDB, ADDW, ADDL, ADDP, ADDF for add byte, word, longword, packed BCD and single-precision floating point, respectively). Like the PDP-11, the Stack Pointer and Program Counter were in the general register file (R14 and R15).

The general form of a VAX-11 instruction would be:

opcode [ operand ] [ operand ]  ...

Each component being one byte, the opcode a value in the range 0–255, and each operand consisting of two nibbles, the upper 4 bits specifying an addressing mode, and the lower 4 bits (usually) specifying a register number (R0–R15).

Unlike the octal-oriented PDP-11, the VAX-11 was a hexadecimal-oriented machine (4-bit sub-byte). This resulted in 16 logical addressing modes (0–15), however, addressing modes 0–3 were "short immediate" for immediate data of 6 bits or less (the 2 low-order bits of the addressing mode being the 2 high-order bits of the immediate data, when prepended to the remaining 4 bits in that data-addressing byte). Since addressing modes 0-3 were identical, this made 13 (electronic) addressing modes, but as in the PDP-11, the use of the Stack Pointer (R14) and Program Counter (R15) created a total of over 15 conceptual addressing modes (with the assembler program translating the source code into the actual stack-pointer or program-counter based addressing mode needed).

The MC68000

Motorola's designers attempted to make the assembly language orthogonal while the underlying machine language was somewhat less so. Unlike PDP-11, the MC68000 used separate registers to store data and the addresses of data in memory.

At the bit level, the person writing the assembler (or debugging machine code) would clearly see that symbolic instructions could become any of several different op-codes. This compromise gave almost the same convenience as a truly orthogonal machine, and yet also gave the CPU designers freedom to use the bits in the instructions more efficiently than a purely orthogonal approach might have.

The 8080 and follow on designs

The 8-bit Intel 8080 (as well as the 8085 and 8051) microprocessor was basically a slightly extended accumulator-based design and therefore not orthogonal. An assembly-language programmer or compiler writer had to be mindful of which operations were possible on each register: Most 8-bit operations could be performed only on the 8-bit accumulator (the A-register), while 16-bit operations could be performed only on the 16-bit pointer/accumulator (the HL-register pair), whereas simple operations, such as increment, were possible on all seven 8-bit registers. This was largely due to a desire to keep all opcodes one byte long and to maintain source code compatibility with the original Intel 8008 (an LSI-implementation of the Datapoint 2200's CPU).

The binary-compatible Z80 later added prefix-codes to escape from this 1-byte limit and allow for a more powerful instruction set. The same basic idea was employed for the Intel 8086, although, to allow for more radical extensions, binary-compatibility with the 8080 was not attempted here; instead the 8086 was designed as a more regular and fully 16-bit processor that was source-compatible with the 8008, 8080, and 8085. It maintained some degree of non-orthogonality for the sake of high code density (even though this was derided as being "baroque" by some computer scientists at the time). The 32-bit extension of this architecture that was introduced with the 80386, was somewhat more orthogonal despite keeping all the 8086 instructions and their extended counterparts. However, the encoding-strategy used still shows many traces from the 8008 and 8080 (and Z80); for instance, single-byte encodings remain for certain frequent operations such as push and pop of registers and constants, and the primary accumulator, eax, employ shorter encodings than the other registers on certain types of operations; observations like this are sometimes exploited for code optimization in both compilers and hand written code.

RISC

A fully orthogonal architecture may not be the most "bit efficient" architecture. In the late 1970s research at IBM (and similar projects elsewhere) demonstrated that the majority of these "orthogonal" addressing modes were ignored by most programs. Perhaps some of the bits that were used to express the fully orthogonal instruction set could instead be used to express more virtual address bits or select from among more registers.

Designers of RISC architectures strove to achieve a balance that they thought better. In particular, most RISC computers, while still being highly orthogonal with regard to which instructions can process which data types, now have reverted to "load/store" architectures. In these architectures, only a very few memory reference instructions can access main memory and only for the purpose of loading data into registers or storing register data back into main memory; only a few addressing modes may be available, and these modes may vary depending on whether the instruction refers to data or involves a transfer of control (jump). Conversely, data must be in registers before it can be operated upon by the other instructions in the computer's instruction set. This trade off is made explicitly to enable the use of much larger register sets, extended virtual addresses, and longer immediate data (data stored directly within the computer instruction).

References

  1. Null, Linda; Lobur, Julia (2010). The Essentials of Computer Organization and Architecture. Jones & Bartlett Publishers. pp. 287–288. ISBN 1449600069.
This article is issued from Wikipedia - version of the 4/4/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.