Lift-to-drag ratio

The Wright brothers testing their gliders in 1901 (left) and 1902 (right). The angle of the tether reflects the dramatic improvement in the lift-to-drag ratio

In aerodynamics, the lift-to-drag ratio, or L/D ratio, is the amount of lift generated by a wing or vehicle, divided by the aerodynamic drag it creates by moving through the air. A higher or more favorable L/D ratio is typically one of the major goals in aircraft design; since a particular aircraft's required lift is set by its weight, delivering that lift with lower drag leads directly to better fuel economy in aircraft, climb performance, and glide ratio.

The term is calculated for any particular airspeed by measuring the lift generated, then dividing by the drag at that speed. These vary with speed, so the results are typically plotted on a 2D graph. In almost all cases the graph forms a U-shape, due to the two main components of drag.

Lift-to-drag ratios can be determined by flight test, by calculation or by testing in a wind tunnel.

Drag

Lift-induced drag is a component of total drag that arises whenever a finite span wing generates lift. At low speeds an aircraft has to generate lift with a higher angle of attack, thereby leading to greater induced drag. This term dominates the low-speed side of the lift versus velocity graph.

The drag curve

Drag polar for light aircraft. The tangent gives the maximum L/D point.

Form drag is caused by movement of the aircraft through the air. This type of drag, also known as air resistance or profile drag varies with the square of speed (see drag equation). For this reason profile drag is more pronounced at higher speeds, forming the right side of the lift/velocity graph's U shape. Profile drag is lowered primarily by streamlining and reducing cross section.

Lift, like drag, increases as the square of the velocity and the ratio of lift to drag is often plotted in terms of the lift and drag coefficients C_L and C_D. Such graphs are referred to as drag polars. Speed increases from left to right. The lift/drag ratio is given by the slope from the origin to some point on this curve and so the peak L/D ratio does not occur at the point of least drag, the leftmost point. Instead it occurs at a slightly higher speed. Designers will typically select a wing design which produces an L/D peak at the chosen cruising speed for a powered fixed-wing aircraft, thereby maximizing economy. Like all things in aeronautical engineering, the lift-to-drag ratio is not the only consideration for wing design. Performance at high angle of attack and a gentle stall are also important.

Glide ratio

As the aircraft fuselage and control surfaces will also add drag and possibly some lift, it is fair to consider the L/D of the aircraft as a whole. As it turns out, the glide ratio, which is the ratio of an (unpowered) aircraft's forward motion to its descent, is (when flown at constant speed) numerically equal to the aircraft's L/D. This is especially of interest in the design and operation of high performance sailplanes, which can have glide ratios approaching 60 to 1 (60 units of distance forward for each unit of descent) in the best cases, but with 30:1 being considered good performance for general recreational use. Achieving a glider's best L/D in practice requires precise control of airspeed and smooth and restrained operation of the controls to reduce drag from deflected control surfaces. In zero wind conditions, L/D will equal distance traveled divided by altitude lost. Achieving the maximum distance for altitude lost in wind conditions requires further modification of the best airspeed, as does alternating cruising and thermaling. To achieve high speed across country, glider pilots anticipating strong thermals often load their gliders (sailplanes) with water ballast: the increased wing loading means optimum glide ratio at higher airspeed, but at the cost of climbing more slowly in thermals. As noted below, the maximum L/D is not dependent on weight or wing loading, but with higher wing loading the maximum L/D occurs at a faster airspeed. Also, the faster airspeed means the aircraft will fly at higher Reynolds number and this will usually bring about a lower zero-lift drag coefficient.

Theory

Mathematically, the maximum lift-to-drag ratio can be estimated as:

,^[1]

where AR is the aspect ratio, the span efficiency factor, a number less than but close to unity for long, straight edged wings, and the zero-lift drag coefficient.

Most importantly, the maximum lift-to-drag ratio is independent of the weight of the aircraft, the area of the wing, or the wing loading.

It can be shown that two main drivers of maximum lift-to-drag ratio for a fixed wing aircraft are wingspan and total wetted area. One method for estimating the zero-lift drag coefficient of an aircraft is the equivalent skin-friction method. For a well designed aircraft, zero-lift drag (or parasite drag) is mostly made up of skin friction drag plus a small percentage of pressure drag caused by flow separation. The method uses the equation:

,^[2]

where is the equivalent skin friction coefficient, is the wetted area and is the wing reference area. The equivalent skin friction coefficient accounts for both separation drag and skin friction drag and is a fairly consistent value for aircraft types of the same class. Substituting this into the equation for maximum lift-to-drag ratio, along with the equation for aspect ratio (), yields the equation:

where b is wingspan. The term is known as the wetted aspect ratio. The equation demonstrates the importance of wetted aspect ratio in achieving an aerodynamically efficient design.

Supersonic/hypersonic lift to drag ratios

At very high speeds, lift to drag ratios tend to be lower. Concorde had a lift/drag ratio of around 7 at Mach 2, whereas a 747 is around 17 at about mach 0.85.

Dietrich Küchemann developed an empirical relationship for predicting L/D ratio for high Mach:^[3]

where M is the Mach number. Windtunnel tests have shown this to be roughly accurate.

Examples

The following table includes some representative L/D ratios.

In gliding flight, the L/D ratios are equal to the glide ratio (when flown at constant speed).

See also

• Lift coefficient
• Thrust specific fuel consumption the lift to drag determines the required thrust to maintain altitude (given the aircraft weight), and the SFC permits calculation of the fuel burn rate
• thrust to weight ratio
• Range (aircraft) range depends on the lift/drag ratio
• Inductrack maglev has a higher lift/drag ratio than aircraft at sufficient speeds
• Gravity drag rockets can have an effective lift to drag ratio while maintaining altitude

References

^[8]

1. ↑ Loftin, LK, Jr. "Quest for performance: The evolution of modern aircraft. NASA SP-468". Retrieved 2006-04-22.  CS1 maint: Multiple names: authors list (link)
2. ↑ Raymer, Daniel (2012). Aircraft Design: A Conceptual Approach (5th ed.). New York: AIAA.  |access-date= requires |url= (help)
3. ↑ Aerospaceweb.org Hypersonic Vehicle Design
4. 1 2 David Noland (February 2005). "The Ultimate Solo". Popular Mechanics. 
5. ↑ "U2 Developments transcript". Central Intelligence Agency. 1960. Lay summary – transcript. 
6. 1 2 3 4 5 6 Antonio Filippone. "Lift-to-Drag Ratios". Advanced topics in aerodynamics. Archived from the original on March 28, 2008. 
7. 1 2 3 Christopher Orlebar (1997). The Concorde Story. Osprey Publishing. p. 116. 
8. 1 2 Cessna Skyhawk II Performance Assessment http://temporal.com.au/c172.pdf
9. ↑ Leishman, J. Gordon. (24 April 2006). Principles of helicopter aerodynamics. Cambridge University Press. p. 230. ISBN 0521858607. The maximum lift-to-drag ratio of the complete helicopter is about 4.5 
10. ↑ Flight performance of the largest volant bird
11. 1 2 Space Shuttle Technical Conference pg 258
12. ↑ http://scienceandglobalsecurity.org/archive/2015/09/hypersonic_boost-glide_weapons.html
13. ↑ Hillje, Ernest R., "Entry Aerodynamics at Lunar Return Conditions Obtained from the Flight of Apollo 4 (AS-501)," NASA TN D-5399, (1969).