Keel

For other uses, see Keel (disambiguation).
Sailing yacht with a fin keel
The initials of Susan Ford Bales being welded into the keel of the aircraft carrier USS Gerald R. Ford (CVN 78) during a keel laying and authentication ceremony at Northrop Grumman Shipbuilding in Newport News.

On boats and ships, keel can refer to either of two parts: a structural element that sometimes resembles a fin and protrudes below a boat along the central line, or a hydrodynamic element. These parts overlap. As the laying down of the keel is the initial step in construction of a ship, in British and American shipbuilding traditions the construction is dated from this event. Only the ship's launching is considered more significant in its creation.

The word can also be used as a synecdoche to refer to a complete boat, such as a keelboat.

Structural keels

A structural keel is the bottom-most structural member around which the hull of a ship is built. The keel runs along the centerline of the ship, from the bow to the stern. The keel is often the first part of a ship's hull to be constructed, and laying the keel, or placing the keel in the cradle in which the ship will be built may mark the start time of its construction. Large, modern ships are now often built in a series of pre-fabricated, complete hull sections rather than being built around a single keel, so shipbuilding process commences with cutting the first sheet of steel.

The most common type of keel is the "flat plate keel", and this is fitted in the majority of ocean-going ships and other vessels. A form of keel found on smaller vessels is the "bar keel", which may be fitted in trawlers, tugs, and smaller ferries. Where grounding is possible, this type of keel is suitable with its massive scantlings, but there is always a problem of the increased draft with no additional cargo capacity. If a double bottom is fitted, the keel is almost inevitably of the flat plate type, bar keels often being associated with open floors, where the plate keel may also be fitted.

Duct keels are provided in the bottom of some vessels. These run from the forward engine room bulkhead to the collision bulkhead and are utilized to carry the double bottom piping. The piping is then accessible when cargo is loaded.

Hydrodynamic keels

A hydrodynamic keel creates lift that minimizes sideways motion, underway.
Lateral resistance effect of a sailing keel
Righting effect of a keel, where A is the center of buoyancy and G is the centre of gravity (hypothetical example).

Non-sailing keels

The keel surface on the bottom of the hull gives the ship greater directional control and stability. In non-sailing hulls, the keel helps the hull to move forward, rather than slipping to the side. In traditional boat building, this is provided by the structural keel, which projects from the bottom of the hull along most or all of its length. In modern construction the bar keel or flat-plate keel performs the same function. There are many types of fixed keels, including full keels, long keels, fin keels, winged keels, bulb keels, and bilge keels among other designs. Deep draft ships will typically have a flat bottom and employ only bilge keels, both to aid directional control and to damp rolling motions

Sailboat keels

In sailboats, keels use the forward motion of the boat to generate lift to counteract the leeward force of the wind. The rudimentary purpose of the keel is to convert the sideways motion of the wind when it is abeam into forward motion. A secondary purpose of the keel is to provide ballast. Keels are different from centreboards and other types of foils in that keels are made of heavy materials to provide ballast to stabilize the boat. Keels may be fixed, or non-movable, or they may retract to allow sailing in shallower waters. Retracting keels may pivot (a swing keel) or slide upwards to retract, and are usually retracted with a winch due to the weight of the ballast. Since the keel provides far more stability when lowered than when retracted (due to the greater moment arm involved), the amount of sail carried is generally reduced when sailing with the keel retracted.

Types of non-fixed keels include swing keels and canting keels. Canting keels can be found on racing yachts, such as those competing in the Volvo Ocean Race. They provide considerably more righting moment as the keel moves out to the windward-side of the boat while using less weight. The horizontal distance from the weight to the pivot is increased, which generates a larger righting moment.

Etymology

The word "keel" comes from Old English cēol, Old Norse kjóll, = "ship" or "keel". It has the distinction of being regarded by some scholars as the very first word in the English language recorded in writing, having been recorded by Gildas in his 6th century Latin work De Excidio et Conquestu Britanniae, under the spelling cyulae (he was referring to the three ships that the Saxons first arrived in).[1][2]

Carina is the Latin word for "keel" and is the origin of the term careen (to clean a keel and the hull in general, often by rolling the ship on its side). An example of this use is Careening Cove, a suburb of Sydney, Australia, where careening was carried out in early colonial days.

See also

Notes

Wikimedia Commons has media related to Keels.
  1. "Gildas, The Ruin of Britain &c. (1899). pp. 4-252. The Ruin of Britain.".
  2. G. W. Whittaker (1970). Collected Essays. Ayer Publishing. p. 44. ISBN 0-8369-1636-0.

Bibliography

This article is issued from Wikipedia - version of the 10/30/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.