Heckler & Koch G41

Heckler & Koch G41

A G41 assault rifle in exhibition
Type Assault rifle
Place of origin West Germany
Service history
Used by See Users
Wars 2007 Lebanon conflict
Production history
Designer Heckler & Koch
Manufacturer Heckler & Koch
Produced 1984-1996
Variants See Variants
Specifications
Weight G41/A1: 4.1 kg (9.04 lb)
G41A2/A3: 4.4 kg (9.7 lb)
G41K: 4.3 kg (9.5 lb)
Length G41/A1: 997 mm (39.3 in)
G41A2/A3: 985 mm (38.8 in) stock extended / 800 mm (31.5 in) stock folded
G41K: 930 mm (36.6 in) stock extended / 740 mm (29.1 in) stock retracted
Barrel length G41: 450 mm (17.7 in)
G41K: 380 mm (15.0 in)
Width 72 mm (2.8 in)
Height 214 mm (8.4 in)

Cartridge 5.56×45mm NATO
Caliber 5.56mm
Action Roller delayed blowback
Rate of fire 850 rounds/min
Muzzle velocity G41 using SS109: 920 m/s (3,018 ft/s)
G41K using SS109: 880 m/s (2,887.1 ft/s)
G41 using M193: 950 m/s (3,116.8 ft/s)
G41K using M193: 910 m/s (2,985.6 ft/s)
Effective firing range 100—400 m sight adjustments
Feed system Various STANAG magazines
Sights Rotary rear diopter drum, hooded front post

The G41 is a German 5.56×45mm NATO assault rifle introduced in 1981 and produced in limited quantities by Heckler & Koch. It was designed to replace the 5.56mm Heckler & Koch HK33 in service providing a more modern weapon platform compatible with contemporary NATO standards.[1] It is chambered for the 5.56×45mm NATO cartridge and can use both SS109 and M193 ammunition. Assembly of the G41 has been discontinued by Heckler & Koch, however, production rights to the rifle were acquired by the Italian arms manufacturer Luigi Franchi.[1]

Design details

Operating mechanism

The G41's engineering origins lay in the 7.92×33mm Kurz StG 45(M) Assault rifle, and later the 7.62×51mm NATO G3 battle rifle.[1] It is a selective fire automatic weapon that employs a roller-delayed blowback system of operation. The two-piece bolt mechanism consists of a bolt head that contains two cylindrical rollers and a wedge-shaped locking piece, attached to a heavy bolt carrier. When fired, the build-up of gas pressure generated by the ignited powder charge exerts rearward pressure on the bolt, which is then transferred onto the rollers. The rollers are cammed inward against appropriately shaped walls in the barrel extension, displacing the locking piece. The geometry of the camming ramps on the wedge-like locking piece ensure a rearward velocity that is greater than that of the bolt. This ensures that the bullet has left the barrel, allowing bore pressures to drop to a safe level before the rollers are fully retracted, clearing the barrel extension notches and releasing the bolt, which is then engaged by the bolt carrier and withdraws together with the entire moving assembly.

Features

The spent cartridge casing extractor is installed inside the bolt head, while the tilting lever ejector is contained in the trigger housing. The rifle is hammer-fired and has a trigger group with a fire control selector that enables semi-automatic, burst and continuous fire. The fire selector's positions are marked with bullet pictograms and it also serves as a manual safety against unintentional discharge. The selector is ambidextrous and its lever is mirrored on both sides of the trigger housing. In the "safe" position, the trigger and sear are disabled.

The firearm uses NATO STANAG magazines (from the M16 rifle) with a capacity of 30 rounds. The magazine release is located on the left side of the rifle, above the magazine well.

The weapon incorporates a manual forward assist that can be used to positively close the bolt, similar to the one used on the American M16A1 rifle, and a side-folding heavy-gauge wire carrying handle which resembles that of the FN FAL. It also has a "hold-open" bolt catch which holds the bolt open after the last round in the magazine has been fired (the bolt release button is just above the magazine release) and has a spring-loaded dust cover that seals the ejection port from debris.

Barrel

The cold hammer-forged barrel has a hexagonal polygonal bore. It comes rifled for either the NATO-standard, Belgian SS109 62 grain bullet with a twist of 178 mm (1:7 in) or in a 305 mm (1:12 in) twist for use with American ammunition with the M193 55 grain projectile. The bore chamber is fluted to assist in the extraction of spent cartridges.[1] The barrel is equipped with a flash suppressor that is also designed to launch rifle grenades.

Sights

The G41 has mechanically adjustable iron sights with a rear rotating diopter drum and hooded front post.[1] The rear sight drum has three apertures of different diameter calibrated for firing at distances of 200, 300 and 400 m and a triangular notch setting preset for firing at 100 m. The receiver housing has recesses in the top cover that permit the use of H&K's proprietary clamp mounts and adapters for NATO-standard optics (such as the Hensoldt 4×24 telescopic sight).

Accessories

Many accessories are based on NATO standard or previously issued items.

The rifle can be fitted with a barrel-mounted bipod based on the one issued with the M16A1's cleaning kit. It also uses the bayonet from the G3. It also can mount the FERO Z24-G 4×24 optical sight on a NATO-standard Picatinny Rail on the receiver.

The G41 can also mount a detachable 40 mm HK79 grenade launcher that replaces the synthetic forearm. The weapon in this configuration is known as the G41TGS, or "Tactical Group Support".

Variants

Users

See also

Notes

  1. 1 2 3 4 5 Woźniak, Ryszard. Encyklopedia najnowszej broni palnej - tom 2 G-Ł. Bellona. 2001. pp22-23.
  2. Web Del Grupo Especial De Operaciones (G.E.O.)
  3. Silahlar
  4. Ian V. Hogg, Modern Weapons of the 20th Century

Bibliography

This article is issued from Wikipedia - version of the 9/6/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.