Hang gliding

Hang glider just after launch

Hang gliding is an air sport or recreational activity in which a pilot flies a light, non-motorized foot-launched heavier-than-air aircraft called a hang glider. Most modern hang gliders are made of an aluminium alloy or composite frame covered with synthetic sailcloth[1] to form a wing. Typically the pilot is in a harness suspended from the airframe, and controls the aircraft by shifting body weight in opposition to a control frame.

Early hang gliders had a low lift-to-drag ratio, so pilots were restricted to gliding down small hills. By the 1980s this ratio significantly improved, and since then pilots can soar for hours, gain thousands of metres of altitude in thermal updrafts, perform aerobatics, and glide cross-country for hundreds of kilometres. The Fédération Aéronautique Internationale and national airspace governing organizations control some regulatory aspects of hang gliding. Obtaining the safety benefits of being instructed is highly recommended.[2][3]

History

Otto Lilienthal in flight

The earliest forms of gliding had existed in China. By the end of the sixth century A.D., the Chinese had managed to build kites large and aerodynamic enough to sustain the weight of an average-sized person. It was only a matter of time before someone decided to simply remove the kite strings and see what happened.[4] Most early glider designs did not ensure safe flight; the problem was that early flight pioneers did not sufficiently understand the underlying principles that made a bird's wing work. Starting in the 1880s technical and scientific advancements were made that led to the first truly practical gliders. Otto Lilienthal built controllable gliders in the 1890s, with which he could ridge soar. His rigorously documented work influenced later designers, making Lilienthal one of the most influential early aviation pioneers. His aircraft was controlled by weight shift and is similar to a modern hang glider.

Jan Lavezzari with a double sail glider

Hang gliding saw a stiffened flexible wing hang glider in 1904, when Jan Lavezzari flew a double lateen sail hang glider off Berck Beach, France. In 1910 in Breslau, the triangle control frame with hang glider pilot hung behind the triangle in a hang glider, was evident in a gliding club's activity.[5] The biplane hang glider was very widely publicized in public magazines with plans for building;[6] such biplane hang gliders were constructed and flown in several nations since Octave Chanute and his tailed biplane hang gliders were demonstrated. In April 1909, a how-to article by Carl S. Bates proved to be a seminal hang glider article that seemingly affected builders even of contemporary times, as several builders would have their first hang glider made by following the plan in his article.[7] Volmer Jensen with a biplane hang glider in 1940 called VJ-11 allowed safe three-axis control of a foot-launched hang glider.[8]

NASA's Paresev glider in flight with tow cable .

On November 23, 1948, Francis Rogallo and Gertrude Rogallo applied for a kite patent[9] for a fully flexible kited wing with approved claims for its stiffenings and gliding uses; the flexible wing or Rogallo wing, which in 1957 the American space agency NASA began testing in various flexible and semi-rigid configurations in order to use it as a recovery system for the Gemini space capsules. The various stiffening formats and the wing's simplicity of design and ease of construction, along with its capability of slow flight and its gentle landing characteristics, did not go unnoticed by hang glider enthusiasts. In 1960-1962 Barry Hill Palmer adapted the flexible wing concept to make foot-launched hang gliders with four different control arrangements.[10] In 1963 Mike Burns adapted the flexible wing to build a towable kite-hang glider he called Skiplane. In 1963, John W. Dickenson adapted the flexible wing airfoil concept to make another water-ski kite glider; for this, the Fédération Aéronautique Internationale vested Dickenson with the Hang Gliding Diploma (2006) for the invention of the "modern" hang glider.[11] Since then, the Rogallo wing has been the most used airfoil of hang gliders.

Components

Hang Gliding

Hang glider sailcloth

There are basically two types of sail materials used in hang glider sails: Woven Polyester Fabrics, and Composite Laminated Fabrics made of some combination of polyester film and polyester fibers.

Woven polyester sailcloth is a very tight weave of small diameter polyester fibers that has been stabilized by the hot-press impregnation of a polyester resin. The resin impregnation is required to provide resistance to distortion and stretch. This resistance is important in maintaining the aerodynamic shape of the sail. Woven polyester provides the best combination of light weight and durability in a sail with the best overall handling qualities.

Laminated sail materials using polyester film achieve superior performance by using a lower stretch material that is better at maintaining sail shape but is still relatively light in weight. The disadvantages of polyester film fabrics is that the reduced elasticity under load generally results in stiffer and less responsive handling, and polyester laminated fabrics are generally not as durable or long lasting as the woven fabrics.

Triangle control frame

In most hang gliders, the control is and has been achieved using a horizontal bar held by the pilot, also known as 'triangle control frame' (TCF), 'control bar' or 'base bar'. This bar is usually pulled to allow for greater speed. Either end of the control bar is attached to an upright, where both extend and are connected to the main body of the glider. This creates the shape of a triangle or A-Frame. In many of these configurations additional wheels or other equipment can be suspended from the bottom bar or rod ends.

Images showing a triangle control frame on Otto Lilienthal's 1892 hang glider prove that the technology of such frames has existed since the early design of gliders, but he did not mention it in his patents. A TCF shows also in Octave Chanute's designs. It was a major part of the now common design of hang gliders by George A. Spratt from 1929. The most simple A-frame that is cable-stayed was demonstrated in a Breslau gliding club hang gliding meet in a battened wing hang glider in the year 1908; hang glider historian Stephan Nitsch has collected instances also of the U control frame used in the first decade of the 1900s; the U is variant of the A-frame.

Training and safety

Learning to hang glide

Due to the poor safety record of early hang gliding pioneers, the sport has traditionally been considered unsafe. Advances in pilot training and glider construction have led to a much improved safety record. Modern hang gliders are very sturdy when constructed to Hang Glider Manufacturers Association, BHPA, Deutscher Hängegleiterverband, or other certified standards using modern materials. Although lightweight they can be easily damaged, either through misuse or by continued operation in unsafe wind and weather conditions. All modern gliders have built-in dive recovery mechanisms such as luff lines in kingposted gliders, or "sprogs" in topless gliders.

Pilots fly in harnesses that support their bodies. Several different types of harnesses exist. Pod harnesses are put on like a jacket and the leg portion is behind the pilot during launch. Once in the air the feet are tucked into the bottom of the harness. They are zipped up in the air with a rope and unzipped before landing with a separate rope. A cocoon harness is slipped over the head and lies in front of the legs during launch. After getting into the air the feet are tucked into it and the back is left open. A knee hanger harness is also slipped over the head but the knee part is wrapped around the knees before launch and just pick up the pilots leg automatically after launch. A supine or suprone harness is a seated harness. The shoulder straps are put on before launch and after take off the pilot slides back into the seat and flies in a seated position.

Pilots carry a parachute enclosed in the harness. In case of serious problems the parachute is manually deployed and carries both pilot and glider down to earth. Pilots also wear helmets and generally carry other safety items such as knives (for cutting their parachute bridle after impact or cutting their harness lines and straps in case of a tree or water landing), light ropes (for lowering from trees to haul up tools or climbing ropes), radios (for communication with other pilots or ground crew), and first-aid equipment.

The accident rate from hang glider flying has been dramatically decreased by pilot training. Early hang glider pilots learned their sport through trial and error and gliders were sometimes home-built. Training programs have been developed for today's pilot with emphasis on flight within safe limits, as well as the discipline to cease flying when weather conditions are unfavorable, for example: excess wind or risk cloud suck.

In the UK there is one death per 116,000 flights, a risk comparable to running a marathon or playing football for a year.[12]

Most pilots learn at recognised courses which lead to the internationally recognised International Pilot Proficiency Information card issued by the FAI.

Launch

Video of a foot-launching from a hill

Launch techniques include foot-launching from a hill, tow-launching from a ground-based tow system, aerotowing (behind a powered aircraft), powered harnesses, and being towed up by a boat. Modern winch tows typically utilize hydraulic systems designed to regulate line tension, this reduces scenarios for lock out as strong winds result in additional length of rope spooling out rather than direct tension on the tow line. Other more exotic launch techniques have also been used successfully, such as hot air balloon drops from very high altitude. When weather conditions are unsuitable to sustain a soaring flight, this results in a top to bottom flight and is referred to as a "sled run". In 1983 Denis Cummings re-introduced a safe tow system that was designed to tow through the centre of mass and had a Gauge that displayed the towing tension, it also integrated a 'weak link' that broke when the safe tow tension was exceeded. After initial testing, in the Hunter Valley, Denis Cummings, pilot, John Clark, (Redtruck), driver and Bob Silver, officianado, began the Flatlands Hang gliding competition at Parkes, NSW. The competition quickly grew, from 16 pilots the first year to hosting a World Championship with 160 pilots towing from several wheat paddocks in western NSW. In 1986 Denis and 'Redtruck' took a group of international pilots to Alice Springs to take advantage of the massive thermals. Using the new system many World records were set. With the growing use of the system, other launch methods were incorporated, static winch and towing behind a powered hang glider or ultralight.

Soaring flight and cross-country flying

Good gliding weather. Well formed cumulus clouds with darker bases suggest active thermals and light winds.

A glider in flight is continuously descending. To achieve an extended flight, the pilot must seek air currents rising faster than the sink rate of the glider. Selecting the sources of rising air currents is the skill that has to be mastered if the pilot wants to achieve flying long distances, known as cross-country (XC). Rising air masses derive from the following sources:[13]

Thermals
The most commonly used source of lift is created by the sun's energy heating the ground which in turn heats the air above it. This warm air rises in columns known as thermals. Soaring pilots quickly become aware of land features which can generate thermals and their trigger points downwind, because thermals have a surface tension with the ground and roll until hitting a trigger point. When the thermal lifts, the first indicator are the swooping birds feeding on the insects being carried aloft, or dust devils or a change in wind direction as the air is pulled in below the thermal. As the thermal climbs, bigger soaring birds indicate the thermal. The thermal rises until it either forms into a cumulus cloud or hits an inversion layer, which is where the surrounding air is becoming warmer with height, and stops the thermal developing into a cloud. Also, nearly every glider contains an instrument known as a variometer (a very sensitive vertical speed indicator) which shows visually (and often audibly) the presence of lift and sink. Having located a thermal, a glider pilot will circle within the area of rising air to gain height. In the case of a cloud street, thermals can line up with the wind, creating rows of thermals and sinking air. A pilot can use a cloud street to fly long straight-line distances by remaining in the row of rising air.
Ridge lift
Ridge lift occurs when the wind encounters a mountain, cliff or hill. The air is pushed up the windward face of the mountain, creating lift. The area of lift extending from the ridge is called the lift band. Providing the air is rising faster than the gliders sink rate, gliders can soar and climb in the rising air by flying within the lift band and at right angle to the ridge. Ridge soaring is also known as slope soaring.
Mountain waves
The third main type of lift used by glider pilots is the lee waves that occur near mountains. The obstruction to the airflow can generate standing waves with alternating areas of lift and sink. The top of each wave peak is often marked by lenticular cloud formations.
Convergence
Another form of lift results from the convergence of air masses, as with a sea-breeze front. More exotic forms of lift are the polar vortices which the Perlan Project hopes to use to soar to great altitudes.[14] A rare phenomenon known as Morning Glory has also been used by glider pilots in Australia.[15]

Performance

Hang glider launching from Mount Tamalpais

With each generation of materials and with the improvements in aerodynamics, the performance of hang gliders has increased. One measure of performance is the glide ratio. For example, a ratio of 12:1 means that in smooth air a glider can travel forward 12 metres while only losing 1 metre of altitude.

Some performance figures as of 2006:

Ballast
The extra weight provided by ballast is advantageous if the lift is likely to be strong. Although heavier gliders have a slight disadvantage when climbing in rising air, they achieve a higher speed at any given glide angle. This is an advantage in strong conditions when the gliders spend only little time climbing in thermals.

Stability and equilibrium

High performance flexible wing hang glider. 2006

Because hang gliders are most often used for recreational flying, a premium is placed on gentle behaviour especially at the stall and natural pitch stability. The wing loading must be very low in order to allow the pilot to run fast enough to get above stall speed. Unlike a traditional aircraft with an extended fuselage and empennage for maintaining stability, hang gliders rely on the natural stability of their flexible wings to return to equilibrium in yaw and pitch. Roll stability is generally set to be near neutral. In calm air, a properly designed wing will maintain balanced trimmed flight with little pilot input. The flex wing pilot is suspended beneath the wing by a strap attached to his harness. The pilot lies prone (sometimes supine) within a large, triangular, metal control frame. Controlled flight is achieved by the pilot pushing and pulling on this control frame thus shifting his weight fore or aft, and right or left in coordinated maneuvers.

Roll
Most flexible wings are set up with near neutral roll due to sideslip (anhedral effect). In the roll axis, the pilot shifts his body mass using the wing control bar, applying a rolling moment directly to the wing. The flexible wing is built to flex differentially across the span in response to the pilot applied roll moment. For example, if the pilot shifts his weight to the right, the right wing trailing edge flexes up more than the left, allowing the right wing to drop and slow down.
Yaw
The yaw axis is stabilized through the sweep back of the wings. The swept planform, when yawed out of the relative wind, creates more lift on the advancing wing and also more drag, stabilizing the wing in yaw. If one wing advances ahead of the other, it presents more area to the wind and causes more drag on that side. This causes the advancing wing to go slower and to fall back. The wing is at equilibrium when the aircraft is traveling straight and both wings present the same amount of area to the wind.
Pitch
The pitch control response is direct and very efficient. It is partially stabilized by the sweep of the wings. The wing centre of gravity is close to the hang point and, at the trim speed, the wing will fly "hands off" and return to trim after being disturbed. The weight-shift control system only works when the wing is positively loaded (right side up). Positive pitching devices such as reflex lines or washout rods are employed to maintain a minimum safe amount of washout when the wing is unloaded or even negatively loaded (upside down). Flying faster than trim speed is accomplished by moving the pilot's weight forward in the control frame; flying slower by shifting the pilot's weight aft (pushing out).

Furthermore, the fact that the wing is designed to bend and flex, provides favourable dynamics analogous to a spring suspension. This provides a gentler flying experience than a similarly sized rigid-winged hang glider.

Instruments

To maximize a pilot's understanding of how the hang glider is flying, most pilots carry instruments. The most basic being a variometer and altimeteroften combined. Some more advanced pilots also carry airspeed indicators and radios. When flying in competition or cross country, pilots often also carry maps and/or GPS units. Hang gliders do not have instrument panels as such, so all the instruments are mounted to the control frame of the glider or occasionally strapped to the pilot's forearm.

Variometer

Main article: Variometer
Vario-altimeter (c. 1998)

Gliding pilots are able to sense the acceleration forces when they first hit a thermal, but have difficulty gauging constant motion. Thus it is difficult to detect the difference between constantly rising air and constantly sinking air. A variometer is a very sensitive vertical speed indicator. The variometer indicates climb rate or sink rate with audio signals (beeps) and/or a visual display. These units are generally electronic, vary in sophistication, and often include an altimeter and an airspeed indicator. More advanced units often incorporate a barograph for recording flight data and/or a built-in GPS. The main purpose of a variometer is in helping a pilot find and stay in the 'core' of a thermal to maximize height gain, and conversely indicating when he or she is in sinking air and needs to find rising air. Variometers are sometimes capable of electronic calculations to indicate the optimal speed to fly for given conditions. The MacCready theory answers the question on how fast a pilot should cruise between thermals, given the average lift the pilot expects in the next thermal climb and the amount of lift or sink he encounters in cruise mode.[16] Some electronic variometers make the calculations automatically, allowing for factors such as the glider's theoretical performance (glide ratio), altitude, hook in weight, and wind direction.

Radio

Aircraft radio

Pilots use 2-way radio for training purposes, for communicating with other pilots in the air, and with their ground crew when traveling on cross-country flights.

One type of radios used are PTT (push-to-talk) handheld transceivers, operating in VHF FM. Usually a microphone is incorporated in the helmet, and the PTT switch is either fixed to the outside of the helmet, or strapped to a finger. Operating a VHF band radio without an appropriate license is illegal in most countries that have regulated airwaves (including United States, Canada, Brazil, etc.), so additional informations must be obtained with the national or local Hang Gliding association.

As aircraft operating in airspace occupied by other aircraft, hang glider pilots also use the appropriate type of radio (i.e. the aircraft transceiver into Aero Mobile Service VHF band). It can, of course, be fitted with a PTT switch to a finger and speakers inside the helmet. The use of aircraft transceivers is subject to regulations specific to the use in the air such as frequencies restrictions, but has several advantages over FM (i.e. frequency modulated) radios used in other services. First is the great range it has (without repeaters) because of its amplitude modulation (i.e. AM). Second is the ability to contact, inform and be informed directly by other aircraft pilots of their intentions thereby improving collision avoidance and increasing safety. Third is to allow greater liberty regarding distance flights in regulated airspaces, in which the aircraft radio is normally a legal requirement. Fourth is the universal emergency frequency monitored by all other users and satellites and used in case of emergency or impending emergency.

GPS

GPS (global positioning system) can be used to mark the flight path as the pilot flies, as it can be interesting to view a GPS track of a flight when back on the ground, to analyze flying technique, and to assist flight performance in competitions and cross country flying, where restricted Airspace needs to be considered.

Records

Records are sanctioned by the FAI. The world record for straight distance is held by Dustin B. Martin (USA), with a distance of 764 km (475 mi) in 2012, originating from Zapata, Texas.[17]

Judy Leden (GBR) holds the altitude record for a balloon-launched hang glider: 11,800 m (38,800 ft) at Wadi Rum, Jordan on October 25, 1994.[18]

Leden also holds the gain of height record: 3,970 m (13,025 ft), set in 1992.[19]

The altitude records for balloon-launched hang gliders:

Altitude Location Pilot Date Reference
38,800' Wadi Rum, Jordan  Judy Leden (ENG) October 25, 1994 [20]
33,000' Edmonton, Alberta, Canada  John Bird (CAN) August 29, 1982 [21]
32,720' California City, California, USA  Stephan Dunoyer (FRA) September 9, 1978 [22]
31,600' Mojave Desert, California, USA  Bob McCaffrey (USA) November 21, 1976 [23]
17,100' San Jose, California, USA  Dennis Kulberg (USA) December 25, 1974 [24]

Competition

Competitions started with "flying as long as possible" and spot landings. With increasing performance, cross-country flying replaced them. Usually two to four waypoints have to be passed with a landing at a goal. In the late 1990s low-power GPS units were introduced and have completely replaced photographs of the goal. Every two years there is a world championship. The Rigid and Women's World Championship in 2006 was hosted by Quest Air in Florida. Big Spring, Texas hosted the 2007 World Championship. Hang gliding is also one of the competition categories in World Air Games organized by Fédération Aéronautique Internationale (World Air Sports Federation - FAI), which maintains a chronology of the FAI World Hang Gliding Championships.[25]

Classes

Modern 'flexible wing' hang glider.

For competitive purposes, there are three classes of hang glider:

In addition to typical launch configurations, a hang glider may be so constructed for alternative launching modes other than being foot launched; one practical avenue for this is for people who physically cannot foot-launch.[26]

Milestones

Flights of the below mentioned distances are rare feats of incredible endurance - these pilots need to be recognized for their achievements. All flights are to be measured as open-distance flights from launch to landing (no additional points in-between as seen in OnLine Contests)

Hang Gliding (Class 1 - Flex Wing)

800KM Club

none to date

700KM Club

600KM Club

500KM Club

Larry Tudor

Jon Durand 557km[27]

Aerobatics

Hang gliders are not certified for aerobatic flight. Pilots perform aerobatics at their own risk. There are three basic maneuvers in a hang glider, not counting a loop, which is actually a climbover with the same entry and exit heading. The following descriptions are excerpts from a nationally recognized rules book:

Official maneuvers
A figure with a bank angle of more than 90° is a maneuver.

Comparison of gliders, hang gliders and paragliders

There can be confusion between gliders, hang gliders, and paragliders. Paragliders and hang gliders are both foot-launched glider aircraft and in both cases the pilot is suspended ("hangs") below the lift surface, but "hang glider" is the default term for those where the airframe contains rigid structures. The primary structure of paragliders is supple, consisting mainly of woven material.

Paragliders Hang gliders Gliders/Sailplanes
Undercarriage pilot's legs used for take-off and landing pilot's legs used for take-off and landing aircraft takes off and lands using a wheeled undercarriage or skids
Wing structure entirely flexible, with shape maintained purely by the pressure of air flowing into and over the wing in flight and the tension of the lines generally flexible but supported on a rigid frame which determines its shape (note that rigid-wing hang gliders also exist) rigid wing surface which totally encases wing structure
Pilot position sitting supine in a seated harness usually lying prone in a cocoon-like harness suspended from the wing; seated and supine are also possible sitting in a seat with a harness, surrounded by a crash-resistant structure
Speed range
(stall speed – max speed)
slower – typically 25 to 60km/h for recreational gliders (over 50km/h requires use of speed bar),[28] hence easier to launch and fly in light winds; least wind penetration; pitch variation can be achieved with the controls faster - stall speed about 30km/h. Never exceed speed up to 90km/h maximum speed up to about 280 km/h (170 mph);[29] stall speed typically 65 km/h (40mph);[29] able to fly in windier turbulent conditions and can outrun bad weather; exceptional penetration into the wind
Maximum glide ratio about 10, relatively poor glide performance makes long distance flights more difficult; current (as of November 2010) world record was just above 500 kilometres (310 mi)[30] 10 (beginners hang glider), 15 (competition flex wing hang glider), 19 (rigid wing hang glider) open class sailplanes – typically around 60:1, but in more common 15–18 meter span aircraft, glide ratios are between 38:1 and 52:1;[31] high glide performance enabling long distance flight, with 3,000 kilometres (1,900 mi) being current (as of November 2010) record[32]
Turn radius tighter turn radius somewhat larger turn radius even greater turn radius but still able to circle tightly in thermals[33]
Landing smaller space needed to land, offering more landing options from cross-country flights; also easier to carry to the nearest road longer approach and landing area required, but can reach more landing areas due to superior glide range when flying cross-country, glide performance can allow glider to reach 'landable' areas, possibly even a landing strip and an aerial retrieve may be possible but if not, specialized trailer needed to retrieve by road. Note some sailplanes have engines that remove the need for an out-landing
Learning simplest and quickest to learn teaching is done in single and two-seat hang gliders teaching is done in a two-seat glider with dual controls
Convenience packs smaller (easier to transport and store) more awkward to transport and store; longer to rig and de-rig; often transported on the roof of a car trailers are typically 10 m (30 ft) long; if it has not been stored in a hangar, rigging & de-rigging takes about 20 minutes
Cost cost of new is €1500 and up,[34] cheapest but shortest lasting (around 500 hours flying time, depending on treatment), active second-hand market[35] €3000 (beginners hang glider) up to €17000 (rigid wing hang glider), life time is more than one decade cost of new glider very high but it is long lasting (up to several decades), so active second-hand market; typical cost is from €2,000 to €145,000[36]

Locations

Locations around the world have been identified as possessing the right combination of characteristics for successful launch and landing sites. Popular sites in the United States include:

In Australia, Bald Hill Stanwell Park is a coastal hang gliding site south of Sydney.

See also

References

Notes

  1. https://www.willswing.com/features/sailcloth.asp
  2. Meadows, G.W. "How to buy a hang glider". www.start-flying.com. Retrieved January 10, 2014.
  3. "Learning to Hang Glide". Hang Gliding Federation of Australia. Retrieved January 10, 2014.
  4. 10 Ancient Chinese Inventions
  5. http://lh4.ggpht.com/_y21JroWG1xg/SG6MAf0c7KI/AAAAAAAAATk/CoCQ25QpLrM/1908StephanNitschCollection.jpg 1908 hang glider in Breslau territory with pilot hung by his left foot, a device used through 1900s (decade) up to today for natural bodily commute.
  6. The Octave Chanute Pages
  7. The Popular Mechanics Glider
  8. VJ-11 Information Page. The history of the VJ-11 hang glider.
  9. Flexible kite
  10. Carl S. Bates
  11. FAI Award: The FAI Hang Gliding Diploma
  12. Risk of dying and sporting activities, retrieved May 31, 2011
  13. Pagen, Dennis (January 1992). Understanding the Sky - A Sport Pilot's Guide to Flying Conditions. Mingoville, Pennsylvania, USA: Dennis Pagen. p. 280. ISBN 978-0-936310-10-7.
  14. Perlan Project
  15. A Guide to the Morning Glory
  16. http://www.modelaircraft.org/museum/bio/MacCready.pdf
  17. http://www.fai.org/record-hang-gliding-and-paragliding
  18. Leden, Judy (2003). Flying with Condors. New York: Orion Books. ISBN 0-7528-0874-5.
  19. "Hang Gliding and Paragliding". www.fai.org. Retrieved 2015-10-22.
  20. Leden, Judy (2003). Flying with Condors. New York: Orion Books. ISBN 0-7528-0874-5.
  21. Edmonton Journal, August 30, 31, 1982; “Kerry Bissell, an official observer of the Soaring Association of Canada: It’s 33,000 feet. If the reading is taken at the top of the trace mark, the record is 11,400 meters”
  22. Hang Gliding magazine, December 1978, p35.
  23. The Guinness Book of Records, 1982.
  24. Sarasota Journal, December 27, 1974 p4D.
  25. Chronology of the FAI World Hang Gliding Championships
  26. Dan Buchanan
  27. Glenday, Craig (2013). The Guiness book of records 2014. Guiness world records limited. ISBN 978-1-908843-15-9.
  28. Technical data for Advance Omega 8 Accessed 22-10-2011
  29. 1 2 Flight Manual of Scheicher ASW27b. Alexander Schleicher GmbH & Co. 2003.
  30. FAI Paragliding record Accessed 2010-11-30.
  31. Handicap list 2008 of the Deutscher Aero Club Accessed 2008-08-07
  32. FAI records Accessed 30 November 2010.
  33. Stewart, Ken (1994). The Glider Pilot's Manual. Airlife Publishing Ltd. p. 257. ISBN 185310504X.
  34. A major manufacturer's price list Accessed 2011-10-21
  35. Typical set of classified ads for paragliders
  36. Typical set of classified ads for gliders

Bibliography

Wikimedia Commons has media related to Hang gliding.
This article is issued from Wikipedia - version of the 12/2/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.