Floodgate

This article is about physical floodgates. For the novel by Alistair MacLean, see Floodgate (novel). For the venture capital fund, see Floodgate Fund.
Tokyo floodgates created to protect from typhoon surges

Floodgates, also called stop gates, are adjustable gates used to control water flow in flood barriers, reservoir, river, stream, or levee systems. They may be designed to set spillway crest heights in dams, to adjust flow rates in sluices and canals, or they may be designed to stop water flow entirely as part of a levee or storm surge system. Since most of these devices operate by controlling the water surface elevation being stored or routed, they are also known as crest gates. In the case of flood bypass systems, floodgates sometimes are also used to lower the water levels in a main river or canal channels by allowing more water to flow into a flood bypass or detention basin when the main river or canal is approaching a flood stage.

Types

Bulkhead gates are vertical walls with movable, or re-movable, sections. Movable sections can be lifted to allow water to pass underneath (as in a sluice gate) and over the top of the structure. Historically, these gates used stacked timbers known as stoplogs or wooden panels known as flashboards to set the dam's crest height. Some floodgates known as coupures in large levee systems slide sideways to open for various traffic. Bulkhead gates can also be made of other materials and used as a single bulkhead unit. Miter gates are used in ship locks and usually close at an 18° angle to approximate an arch.
A sluice gate on the Harran canal
A flood wall gate at Harlan, Kentucky
Hinged crest gates, are wall sections that rotate from vertical to horizontal, thereby varying the height of the dam. They are generally controlled with hydraulic power, although some are passive and are powered by the water being impounded. Variations:
  • flap gate
  • fish-belly flap gates
  • Bascule gates
  • Pelican gates
A hinged crest gate during installation
Fish belly flap gates at the Scrivener Dam, Canberra
Radial gates are rotary gates consisting of cylindrical sections. They may rotate vertically or horizontally. Tainter gates are a vertical design that rotates up to allow water to pass underneath. Low friction trunnion bearings, along with a face shape that balances hydrostatic forces, allow this design to close under its own weight as a safety feature.
Tainter gate diagram
Tainter gates and spillway
Drum gates are hollow gate sections that float on water. They are pinned to rotate up or down. Water is allowed into or out of the flotation chamber to adjust the dam's crest height.
Drum gates are controlled with valves.
Drum gates on a diversion dam
  • Roller gates are large cylinders that move in an angled slot. They are hoisted with a chain and have a cogged design that interfaces with their slot.
  • Clamshell gates have an external clamshell leaf design.
A roller gate on the Mississippi.
Clamshell floodgates at the Arrowrock Dam.
Fusegates are a mechanism designed to provide the controlled release of water in the event of exceptionally large floods. The design consists of free standing blocks (the fusegates) set side by side on a flattened spillway sill. The Fusegate blocks act as a fixed weir most of the time, but in excessive flood conditions they are designed to topple forward, allowing the controlled discharge of water. Multiple fusegates are generally set up side by side, with each fusegate designed to release under progressively extreme flooding, thus minimizing the impact of the floodwater on the river downstream.[1] The System is developed and patented by Hydroplus from Paris, France. It has been installed on more than 50 dams around the world with sizes ranging from 1 m to more than 9 m in height. Fusegate are typically used to increase the storage capacity of existing dams or to maximize the discharge potential of undersized spillways.
Typical fusegate sketch
Mitre gates

Valves

Discharge from a Howell-Bunger valve

Valves used in floodgate applications have a variety of design requirements and are usually located at the base of dams. Often, the most important requirement (besides regulating flow) is energy dissipation. Since water is very heavy, it exits the base of a dam with the enormous force of water pushing from above. Unless this energy is dissipated, the flow can erode nearby rock and soil and damage structures.

Other design requirements include taking into account pressure head operation, the flow rate, whether the valve operates above or below water, and the regulation of precision and cost.

Physics

In order to do a simple calculation of the force on a rectangular flood gate one can use the following equation:

where:

F = force measured in the SI units kg·m·s−2 which is called the newton (N)
p = pressure measured in N/m2, which is called the pascal (Pa)
where:
A = area = rectangle : length × height measured in m2
where:
length = the horizontal length of a rectangular floodgate measured in meters
height = the height of a non-submerged flood gate from the bottom of the water column to the water surface measured in meters

If the rectangular flood gate is submerged below the surface the same equation can be used but only the height from the water surface to the middle of the gate must be used to calculate the force on the flood gate.

See also

Wikimedia Commons has media related to Floodgate.

References

  1. "Fusegate Operation". www.Hydroplus.com. Retrieved 2013-11-21.

Sources

This article is issued from Wikipedia - version of the 3/18/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.