ESTCube-1

ESTCube-1

ESTCube-1 illustration
Mission type Technology
Operator University of Tartu
COSPAR ID 2013-021C
SATCAT № 39161
Website http://www.estcube.eu/en/home
Mission duration 12 months
Spacecraft properties
Launch mass 1.048 kilograms (2.31 lb)
Dry mass 1.048 kilograms (2.31 lb)
Power 3.6W [1]
Start of mission
Launch date 7 May 2013, 02:06:31 (2013-05-07UTC02:06:31Z) UTC
Rocket Vega
Launch site Kourou ELA-1
Contractor ESA
End of mission
Deactivated 17 Feb 2015, 10:27:00 (2015-02-17UTC10:27Z) UTC[2]
Last contact 19 May 2015[1]
Decay date 2038*estimated
Orbital parameters
Reference system Geocentric
Regime Low Earth
Perigee 665 km
Apogee 665 km
Inclination 98.129 degrees
Period 98.03 minutes

ESTCube-1 is the first Estonian satellite and first satellite in the world to attempt to use an electric solar wind sail (e-sail). Developed as part of the Estonian Student Satellite Program, it was launched on 7 May 2013 aboard a Vega carrier rocket[3] and successfully deployed into orbit.[4] Student Satellite is an educational project in which university and high school students can participate.[5][6] The CubeSat standard for nanosatellites was followed during the engineering of ESTCube-1, resulting in a 10x10x11.35 cm cube, with a volume of 1 liter and a mass of 1.048 kg.[7][8]

Mission ended in 17 February 2015 and it was said that during this time it resulted 29 bachelor's and 19 master's dissertations, 5 doctoral theses and 4 start-ups.[9]

Scientific purpose

The first image of Earth taken by ESTCube-1 on May 15, 2013.[4]
ESTCube-1 E-sail experiment
The structure illustration of cubesat ESTCube-1
ESTCube-1 structure

While emphasis was placed on educating students during creation of ESTCube-1, it does have a scientific purpose. On board the satellite is an electric solar wind sail (E-Sail) which was invented by Finnish scientist Pekka Janhunen. During the ESTCube-1 flight, 10 meters of 20–50 micrometer thick E-Sail wire, sometimes referred to as "Heytether," were deployed from the satellite. The deployment of the Heytether is detected by a decrease of the satellite's rotation speed or an onboard camera.[10]

To control the E-Sail element's interaction with both the plasma surrounding the Earth and the effect it has on the spacecraft's spinning speed, two nanotechnology electron emitters/guns are on board. The electron emitters are connected to the E-Sail element which it loads positively to 500 volts by shooting out electrons. The positive ions in the plasma were intended to push the E-Sail element and influence the satellite's rotation speed. The effect of the plasma on the E-Sail was to be measured by the change in said rotation speed. The tether was also intended to de-orbit the satellite y use as a plasma-brake to demonstrate a possibility for returning small satellites from orbit. A color CMOS camera is also on board that is capable of making RAW-format pictures with VGA-resolution. This camera is used to acquire images of Earth and to monitor deployment of the Heytether.

Orbit

To complete the scientific experiment and communicate with the satellite on several occasions the orbit chosen was a sun–synchronous circular orbit at an altitude of 670 kilometers. ESTCube-1 was launched into orbit by Arianespace, using a Vega rocket which lifted off from ELA-1 at Kourou at 02:06:31 UTC on 7 May 2013. The satellite was placed into orbit and communication successfully established,[11] with the first photo of the Earth taken on May 15 and transmitted to the ground on the amateur radio band.[4]

Lifespan of the satellite

The plan, beginning with the 7 May 2013 launch, included the following steps:

End of Mission

The last morse code transmission was transmitted on 17 February 2015. The mission ended due to degradation of the photovoltaic power system[1] and subsequently the batteries became exhausted. The plan to test a solar sail the satellite carried, failed since the sail cable unwinding mechanics did not survive the rocket takeoff vibration.[12]

Design

Measurements and weight

During the development of the Estonian satellite mission it was decided to make a 1U CubeSat. By standard 1 unit (1U) CubeSat base side length must be 100.0±0.1 millimeters and satellite height must be 113.5±0.1 mm. Mass is also set in CubeSat standard, the highest possible mass for 1U CubeSat is 1300 grams.

Communications

Communication from the satellite is made at two International Amateur Radio Unions registered frequencies

Periodic but very slow communication is made by using 18 WPM telegraphy signal on a frequency of 437.250 MHz. At that frequency, the most important satellite parameters are returned every 3 to 10 minutes. For fast connections FSK-modulation radio signals on a frequency of 437.505 MHz with a 9600 baud connection speed and AX.25 packet standard is used. The relatively slow connection speeds result from the use of amateur radio frequencies which limits the bandwidth to 25 kilohertz. The fast connection is used only when the satellite has been given a specific order. Both telegraphy and packet telemetry protocols of ESTCube-1 are published on project webpage.[14][15]

Commands sent to the satellite use the 145 MHz (2 meter) amateur band.

Software

ESTCube-1 microcontrollers use the following operating systems:

Mission Control System is currently being developed by the students of Tartu University under the supervision of the company CGI Group.

Financing and costs

ESTCube-1 presentation in January 2013.

The least expensive satellite launch is offered by the European Space Agency. Because Estonia is an associated member of ESA, most of the launch expenses (about 70,000 euros) were covered by the Estonian member fee for educational expenses. With the launch, total expenses for the project were approximately 100,000 euros.

Results

The satellite successfully demonstrated the operation of the systems in space, with a two-year operational life. The tether system to deploy the e-sail failed to deploy, and no measurements were taken of the e-sail or of the plasma braking deployment system.

See also

References

  1. 1 2 3 4 Vladislav-Veniamin Pustõnski, ESTCube-1 ceased working after 2 years in orbit, Estonian Space Office (accessed 8 June 2016)
  2. "ESTCube-1's 651-day career: 53 dissertations and a marriage proposal". 17 Feb 2015.
  3. ESA: Launch schedule
  4. 1 2 3 Southgate Radio Amateur News, First picture from ESTCube-1 ham radio CubeSat, May 22, 2013 (accessed Aug. 16 2013)
  5. "The two primary payloads for Vega's second launch are readied at the Spaceport". Arianespace. March 14, 2013. Retrieved March 25, 2013.
  6. "Arianespace Awaits... Vega Tops Off While Sats Prep For Vegies (Launch)". satnews. March 14, 2013. Retrieved March 25, 2013.
  7. "Estonia's student cubesat satellite is ready for the next Vega launch". Arianespace. Retrieved March 25, 2013.
  8. "ESTCube-1 mentioned in Nature's regional report". 17 Nov 2010.
  9. "ESTCube-1's 651-day career: 53 dissertations and a marriage proposal" ERR, 17 February 2015
  10. "Proba-V's fellow passenger" (PDF). European Space Agency. February 2013. p. 17. Retrieved March 25, 2013.
  11. Matteo Emanuelli, Estonian Cubesat on a Collision Course with Iridium-Cosmos Debris, August 1, 2013, Space Safety News (accessed Aug. 16 2013)
  12. "ESTCube-1 sends its last words: "Long live Estonia!"". 17 Feb 2015.
  13. "ESTCube-1". International Amateur Radio Union. 15 Mar 2013. Retrieved March 25, 2013.
  14. "Telemetry packet description". Retrieved August 5, 2014.
  15. "Beacon decoding". Retrieved August 5, 2014.

External links

Wikimedia Commons has media related to ESTCube-1.
Videos
This article is issued from Wikipedia - version of the 11/25/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.