Directivity

Diagram showing directivity

Antennas
Part of a series on

Common types Dipole Fractal Loop Satellite dish Television Whip
Components Balun Block upconverter Coaxial cable Counterpoise (ground system) Feed Feed line Low-noise block downconverter Passive radiator Receiver Rotator Stub Transmitter Tuner Twin-lead
Systems Antenna farm Amateur radio Cellular network Hotspot Municipal wireless network Radio Radio masts and towers Wi-Fi Wireless
Safety and regulation Mobile phone radiation and health Wireless electronic devices and health International Telecommunication Union (Radio Regulations) World Radiocommunication Conference
Radiation sources / regions Boresight Focal cloud Ground plane Main lobe Near and far field Side lobe Vertical plane
Characteristics Array gain Directivity Efficiency Electrical length Equivalent radius Factor Friis transmission equation Gain Height Radiation pattern Radiation resistance Radio propagation Radio spectrum Signal-to-noise ratio Spurious emission
Techniques Beam steering Beam tilt Beamforming Bell Laboratories Layered Space-Time (BLAST) Multiple-input multiple-output (MIMO) Reconfiguration Spread spectrum Wideband Space Division Multiple Access (WSDMA)

In electromagnetics, directivity is a figure of merit, usually for an antenna. It measures the power density the antenna radiates in the direction of its strongest emission, versus the power density radiated by an ideal isotropic radiator (which emits uniformly in all directions) radiating the same total power.

An antenna's directivity is a component of its gain; the other component is its (electrical) efficiency. Directivity is an important measure because most emissions are intended to go in a particular direction or at least in a particular plane (horizontal or vertical); emissions in other directions or planes are wasteful (or worse).

The directivity of an actual antenna can vary from 1.76 dBi for a short dipole, to as much as 50 dBi for a large dish antenna.^[1]

Definition

The directivity, D, of an antenna is the maximal value of its directive gain. Directive gain is represented as $D(\theta ,\phi )$ and compares the radiant intensity (power per unit solid angle) $U(\theta ,\phi )$ that an antenna creates in a particular direction against the average value over all directions:

D(\theta ,\phi )={\frac {U(\theta ,\phi )}{P_{\text{tot}}/\left(4\pi \right)}}.

Here $\theta$ and $\phi$ are the standard spherical coordinate angles, $U(\theta ,\phi )$ is the radiation intensity, which is the power density per unit solid angle, and $P_{\text{tot}}$ is the total radiated power. The quantities $U(\theta ,\phi )$ and $P_{\text{tot}}$ satisfy the relation

P_{\text{tot}}=\int _{\phi =0}^{\phi =2\pi }\int _{\theta =0}^{\theta =\pi }U\sin \theta \,d\theta \,d\phi ;

that is, the total radiated power $P_{\text{tot}}$ is the power per unit solid angle $U(\theta ,\phi )$ integrated over a spherical surface. Since there are 4π steradians on the surface of a sphere, the quantity $P_{\text{tot}}/(4\pi )$ represents the average power per unit solid angle.

In other words, directive gain is the radiation intensity of an antenna at a particular $(\theta ,\phi )$ coordinate combination divided by what the radiation intensity would have been had the antenna been an isotropic antenna radiating the same amount of total power into space.

Directivity, then, is the maximal directive gain value found among all possible solid angles:

{\begin{aligned}D&=\max \left({\frac {U}{P_{\text{tot}}/\left(4\pi \right)}}\right)\\&={\frac {\left.U(\theta ,\phi )\right|_{\text{max}}}{{\frac {1}{4\pi }}\int _{0}^{2\pi }\int _{0}^{\pi }U(\theta ,\phi )\sin \theta \,d\theta \,d\phi }}.\end{aligned}}

The word directivity is also sometimes used as a synonym for directive gain. This usage is readily understood, as the direction will be specified, or directional dependence implied. Later editions of the IEEE Dictionary^[2] specifically endorse this usage; nevertheless it has yet to be universally adopted.

Relation to beam width

The beam solid angle, represented as $\Omega _{A}$ , is defined as the solid angle which all power would flow through if the antenna radiation intensity were constant at its maximal value. If the beam solid angle is known, then directivity can be calculated as

D={\frac {4\pi }{\Omega _{A}}},

which simply calculates the ratio of the beam solid angle to the solid angle of a sphere.

The beam solid angle can be approximated for antennas with one narrow major lobe and very negligible minor lobes by simply multiplying the half-power beamwidths (in radians) in two perpendicular planes. The half-power beamwidth is simply the angle in which the radiation intensity is at least half of the peak radiation intensity.

The same calculations can be performed in degrees rather than in radians:

D\approx 4\pi {\frac {({\frac {180}{\pi }})^{2}}{\Theta _{1d}\Theta _{2d}}}={\frac {41253}{\Theta _{1d}\Theta _{2d}}},

where $\Theta _{{1d}}$ is the half-power beamwidth in one plane (in degrees) and $\Theta _{{2d}}$ is the half-power beamwidth in a plane at a right angle to the other (in degrees).

In planar arrays, a better approximation is

D\approx {\frac {32400}{\Theta _{1d}\Theta _{2d}}}.

Expression in decibels

The directivity is rarely expressed as the unitless number $D$ but rather as a decibel comparison to a reference antenna:

D_{\text{dB}}=10\cdot \log _{10}\left[{\frac {D}{D_{\text{reference}}}}\right].

The reference antenna is usually the theoretical perfect isotropic radiator, which radiates uniformly in all directions and hence has a directivity of 1. The calculation is therefore simplified to

D_{\text{dBi}}=10\cdot \log _{10}D.

Another common reference antenna is the theoretical perfect half-wave dipole, which radiates perpendicular to itself with a directivity of 1.64:

D_{\text{dBd}}=10\cdot \log _{10}\left[{\frac {D}{1.64}}\right].

Accounting for polarization

When polarization is taken under consideration, three additional measures can be calculated:

Partial directive gain

Partial directive gain is the power density in a particular direction and for a particular component of the polarization, divided by the average power density for all directions and all polarizations. For any pair of orthogonal polarizations (such as left-hand-circular and right-hand-circular), the individual power densities simply add to give the total power density. Thus, if expressed as dimensionless ratios rather than in dB, the total directive gain is equal to the sum of the two partial directive gains.^[2]

Partial directivity

Partial directivity is calculated in the same manner as the partial directive gain, but without consideration of antenna efficiency (i.e. assuming a lossless antenna). It is similarly additive for orthogonal polarizations.

Partial gain

Partial gain is calculated in the same manner as gain, but considering only a certain polarization. It is similarly additive for orthogonal polarizations.

Main article: Antenna gain

In other areas

The term directivity is also used with other systems.

With directional couplers, directivity is a measure of the difference in dB of the power output at a coupled port, when power is transmitted in the desired direction, to the power output at the same coupled port when the same amount of power is transmitted in the opposite direction.^[3]

In acoustics, it is used as a measure of the radiation pattern from a source indicating how much of the total energy from the source is radiating in a particular direction. In electro-acoustics, these patterns commonly include omnidirectional, cardioid and hyper-cardioid microphone polar patterns. A loudspeaker with a high degree of directivity (narrow dispersion pattern) can be said to have a high Q.^[4]

References

↑ Antenna Tutorial
1 2 Institute of Electrical and Electronics Engineers, “The IEEE standard dictionary of electrical and electronics terms”; 6th ed. New York, N.Y., Institute of Electrical and Electronics Engineers, c1997. IEEE Std 100-1996. ISBN 1-55937-833-6 [ed. Standards Coordinating Committee 10, Terms and Definitions; Jane Radatz, (chair)]
↑ App note, Mini-Circuits directional couplers
↑ Rane Professional Audio Reference Home

Coleman, Christopher (2004). "Basic Concepts". An Introduction to Radio Frequency Engineering. Cambridge University Press. ISBN 0-521-83481-3.

This article is issued from Wikipedia - version of the 7/7/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.