Curve orientation

This article is about closed curves. For the orientation of open curves, see Differential geometry of curves ยง Tangent vectors.

In mathematics, a positively oriented curve is a planar simple closed curve (that is, a curve in the plane whose starting point is also the end point and which has no other self-intersections) such that when traveling on it one always has the curve interior to the left (and consequently, the curve exterior to the right). If in the above definition one interchanges left and right, one obtains a negatively oriented curve.

Crucial to this definition is the fact that every simple closed curve admits a well-defined interior; that follows from the Jordan curve theorem.

All simple closed curves can be classified as negatively oriented (clockwise), positively oriented (counterclockwise), or non-orientable. The inner loop of a beltway road in the United States (or other countries where people drive on the right side of the road) would be an example of a negatively oriented (clockwise) curve. A circle oriented counterclockwise is an example of a positively oriented curve. The same circle oriented clockwise would be a negatively oriented curve.

The concept of orientation of a curve is just a particular case of the notion of orientation of a manifold (that is, besides orientation of a curve one may also speak of orientation of a surface, hypersurface, etc.). Here, the interior and the exterior of a curve both inherit the usual orientation of the plane. The positive orientation on the curve is then the orientation it inherits as the boundary of its interior; the negative orientation is inherited from the exterior.

Orientation of a simple polygon

In two dimensions, given an ordered set of three or more connected vertices (points) (such as in connect-the-dots) which forms a simple polygon, the orientation of the resulting polygon is directly related to the sign of the angle at any vertex of the convex hull of the polygon, for example, of the angle ABC in the picture. In computations, the sign of the smaller angle formed by a pair of vectors is typically determined by the sign of the cross product of the vectors. The latter one may be calculated as the sign of the determinant of their orientation matrix. In the particular case when the two vectors are defined by two line segments with common endpoint, such as the sides BA and BC of the angle ABC in our example, the orientation matrix may be defined as follows:

A formula for its determinant may be obtained, e.g., using the method of cofactor expansion:

If the determinant is negative, then the polygon is oriented clockwise. If the determinant is positive, the polygon is oriented counterclockwise. The determinant is non-zero if points A, B, and C are non-collinear. In the above example, with points ordered A, B, C, etc., the determinant is negative, and therefore the polygon is clockwise.

Practical considerations

In practical applications, the following considerations are commonly taken into an account.

One does not need to construct the convex hull of a polygon to find a suitable vertex. A common choice is the vertex of the polygon with the smallest X-coordinate. If there are several of them, the one with the smallest Y-coordinate is picked. It is guaranteed to be the vertex of the convex hull of the polygon. Alternatively, the vertex with the smallest Y-coordinate among the ones with the largest X-coordinates or the vertex with the smallest X-coordinate among the ones with the largest Y-coordinates (or any other of 8 "smallest, largest" X/Y combinations) will do as well.

If the orientation of a convex polygon is sought, then, of course, any vertex may be picked.

For numerical reasons, the following equivalent formula for the determinant is commonly used:

The latter formula has four multiplications less. What is more important in computer computations involved in most practical applications, such as computer graphics or CAD, the absolute values of the multipliers are usually smaller (e.g., when A, B, C are within the same quadrant), thus giving a smaller numerical error or, in the extreme cases, avoiding the arithmetic overflow.

When it is not known in advance that the sequence of points defines a simple polygon, the following things must be kept in mind.

For a self-intersecting polygon (complex polygon) (or for any self-intersecting curve) there is no natural notion of the "interior", hence the orientation is not defined. At the same time, in geometry and computer graphics there are a number of concepts to replace the notion of the "interior" for closed non-simple curves; see, e.g., "flood fill" and "winding number".

In "mild" cases of self-intersection, with degenerate vertices when three consecutive points are allowed be on the same straight line and form a zero-degree angle, the concept of "interior" still makes sense, but an extra care must be taken in selection of the tested angle. In the given example, imagine point A to lie on segment BC. In this situation the angle ABC and its determinant will be 0, hence useless. A solution is to test consecutive corners along the polygon (BCD, DEF,...) until a non-sero determinant is found (unless all points lie on the same straight line). (Notice that the points C, D, E are on the same line and form a 180-degree angle with zero determinant.)

Local concavity

Once the orientation of a polygon formed from an ordered set of vertices is known, the concavity of a local region of the polygon can be determined using a second orientation matrix. This matrix is composed of three consecutive vertices which are being examined for concavity. For example, in the polygon pictured above, if we wanted to know whether the sequence of points F-G-H is concave, convex, or collinear (flat), we construct the matrix

If the determinant of this matrix is 0, then the sequence is collinear - neither concave nor convex. If the determinant has the same sign as that of the orientation matrix for the entire polygon, then the sequence is convex. If the signs differ, then the sequence is concave. In this example, the polygon is negatively oriented, but the determinant for the points F-G-H is positive, and so the sequence F-G-H is concave.

The following table illustrates rules for determining whether a sequence of points is convex, concave, or flat:

Negatively oriented polygon (clockwise) Positively oriented polygon (counterclockwise)
determinant of orientation matrix for local points is negative convex sequence of points concave sequence of points
determinant of orientation matrix for local points is positive concave sequence of points convex sequence of points
determinant of orientation matrix for local points is 0 collinear sequence of points collinear sequence of points

See also

References

    External links

    This article is issued from Wikipedia - version of the 10/31/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.