Consumer IR

Consumer IR, consumer infrared, or CIR, refers to a wide variety of devices employing the infrared electromagnetic spectrum for wireless communications. Most commonly found in television remote controls, infrared ports are equally ubiquitous in consumer electronics, such as PDAs, laptops, and computers. The functionality of CIR is as broad as the consumer electronics that carry it. For instance, a television remote control can convey a "channel up" command to the television, while a computer might be able to surf the internet solely via CIR. The type, speed, bandwidth, and power of the transmitted information depends on the particular CIR protocol employed.

CIR is the most common type of free-space optical communication.

Protocol description

Since the Consumer IR protocols are for the most part not standardized, computers and universal remotes often memorize a bit stream, possibly with compression and possibly without determining the actual bit rate, and play it back. Similarities between remotes are often largely the accidental result of the finite selection of infrared encoder/decoder chips (though now microcontrollers are also used) and IR receiver modules or imitation of the older chips rather than by design. Manufacturers of consumer appliances often reuse the same protocol on many similar devices, though for each manufacturer and device type there are usually multiple protocols in use. The code listings inform about for any universal remote.

CIR and protocol implementation

With the ready availability of inexpensive microcontroller chips, many remotes may be based on such chips today rather than dedicated remote control encoder chips. This makes it easier to keep the same codes when moving the buttons on the remote.

Also, the decoder functionality will often be integrated into a more complicated micro-controller that controls the A/V device, eliminating the need for the separate chip. In the absence of a viable standard, the microcontrollers can be used to emulate the ambiguous protocols used by the old dedicated encoder/decoder chips and it appears that this is often the case. There are even stripped down 4-bit mask-programmable microcontrollers designed only for remote control use (such as NEC's µPD612xA (discontinued), µPD613x, µPD1724x, µPD6x; and µPD17932x 8-bit family[1]). These offer keyboard wake, low power standby modes, and sample controller code though similar features are present on more general PIC microcontrollers or Atmel AVRs.

CIR influences in other devices

Some infrared wireless laptop keyboards and mice use protocols similar to Consumer IR devices. Some PC remote controls used for controlling computer media players, controlling presentation software, or other applications also use Consumer IR style protocols. Some computer remotes, keyboards, and mice may also use IrDA protocol though IrDA was designed for very short range use.

Standards

Sony manufactured a number of consumer devices of different types that share a common proprietary protocol, called S-link. A jack on each device allowed the remote control signals to be interconnected between devices. The protocol included the useful but unusual feature of supporting more than one of the same type of device (such as multiple CD changers). Some A/V components could generate informational status codes that could be used to do things like automatically stop your tape deck when the CD you were recording stopped playing. Software running on a PC with a suitable interface could also control the A/V components and monitor their activity; for example, your computer could tell what disk and track were playing in your CD changer and look up the titles in one of the internet CD databases. Sony charges 5000 USD for access to the S-Link documentation.[2] Sony use the SIRC protocol for remote controls. SIRC is developed in three different versions: 12 bit, 15 bit and 20 bit. After 12 bits have been received, the receiver waits to see if there are more falling edges to know if the SIRC protocol is 15 bit or 20 bit coded.

The RECS-80 and RC-5 codes developed by Philips have been casually referred to as international standards.[3][4] However, the RECS-80 protocol was prone to interference and was quickly replaced by the RC-5 protocol. Although it appears that they were proprietary protocols developed by Philips, they were also adopted by various other manufacturers, specifically European- and US-based ones. This allowed interoperability between the remote handsets and equipment of various brands. The RC-5 code was, and still is, used by many US- and European-based manufacturers of specialty audio/video equipment. Unfortunately, documentation of the standard commands were not widely distributed. Therefore, there are some brands of equipment that use non-standard commands, causing interference with other equipment also using the RC-5 protocol.

The RC-5 command set was defined in the late 1980s and expanded to increase the number of commands in the early 1990s (sometimes called RC-5x). However, the rapidly expanding requirements for newer categories of electronics products since that time (e.g., DVD players, cable boxes, DVR's, et cetera) has led Philips to replace the RC-5 protocol with the newer RC-6 protocol that has both an expanded set of devices (256 versus 32) and commands per device (256 versus 64 in RC-5 and 128 in RC-5x). Again, information on the RC-6 protocol is not readily available from Philips.

In contrast, the major Japanese consumer electronics manufacturers almost universally adopted a protocol that was developed and administered by NEC. In the NEC protocol, each manufacturer is assigned a unique code that is contained in the transmitted command, avoiding the possibility of false triggering by other remote handsets.

RECS-80 uses pulse position modulation and RC-5 uses bi-phase. Early dedicated-purpose chips were offered by Philips Semiconductors to allow for the easy use of RECS-80 and RC-5 protocols. The SAA3004, SAA3007, and SAA3008 encoder chips used RECS-80, and the SAA3006 and SAA3010 encoder chips used RC-5. The SAA3049A decoder chip decoded either type. (Note that the Philips Semiconductors division is now NXP). All of these chips have been discontinued. However, these transmission protocols are easily created and/or decoded with general-purpose 8-bit microcontrollers, such as those offered by Microchip Technology and Atmel.

Transmission of the IR commands requires only a microcontroller and an infrared LED, available from a wide variety of sources. Reception of the modulated commands for RC-5, RC-6, and the NEC protocols is easily accomplished with specialized IR receivers, most readily available from Sharp Corporation and Vishay Intertechnology. These receivers include a photo-diode, an automatic gain control (AGC) circuit, and a demodulator. The demodulated signal is then decoded with a microcontroller.

CEA-931-B defines a method for encapsulating remote control codes over IP and CEA-931-A defines a method for encapsulating remote control codes over IEEE-1394 . These documents are not free even though free standards are the norm for Internet Protocols and contributed significantly to their widespread adoption.

Protocol limitations

The lack of standardization creates many problems for consumers: the need to purchase universal remotes because the original cannot control related functions on interconnected devices and to upgrade them when buying a new device, universal remotes that do not adequately control the devices, inability to control more than one of the same type unit, the inability in most consumer setups to stop tape recording when CD ends, the inability of VCRs to control cable channels, and others. This in addition to having 5+ different remotes on the coffee table.

Technical information

See also

Notes

  1. "UPD17932x(Non Promotion)". Support for the UPD17932x Group is limited to customers who have already adopted these products. If adopting new products, please consider other ranges such as the RL78/L12 Group.
  2. Sony S-Link Resource Center
  3. Juergen Putzger. Decoding IR Remote controls
  4. Eric Maass (2001). 'How does a universal remote control work?', MadSci
  5. Lamp Section, National Electrical Manufacturers Association (1998). Interaction of Infrared Controls And Electronic Compact Fluorescent Lamps
  6. ePanorama. Infrared remote control technology
  7. http://www.vishay.com/docs/82486/tsmp58138.pdf

External links

This article is issued from Wikipedia - version of the 10/26/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.