Codd's cellular automaton

Codd's cellular automaton is a cellular automaton (CA) devised by the British computer scientist Edgar F. Codd in 1968. It was designed to recreate the computation- and construction-universality of von Neumann's CA but with fewer states: 8 instead of 29. Codd showed that it was possible to make a self-reproducing machine in his CA, in a similar way to von Neumann's universal constructor, but never gave a complete implementation.

History

In the 1940s and '50s, John von Neumann posed the following problem:[1]

He was able to construct a cellular automaton with 29 states, and with it a universal constructor. Codd, building on von Neumann's work, found a simpler machine with eight states.[2] This modified von Neumann's question:

Three years after Codd's work, Edwin Roger Banks showed a 4-state CA in his PhD thesis that was also capable of universal computation and construction, but again did not implement a self-reproducing machine.[3] John Devore, in his 1973 masters thesis, tweaked Codd's rules to greatly reduce the size of Codd's design, to the extent that it could be implemented in the computers of that time. However, the data tape for self-replication was too long; Devore's original design was later able to complete replication using Golly. Christopher Langton made another tweak to Codd's cellular automaton in 1984 to create Langton's loops, exhibiting self-replication with far fewer cells than that needed for self-reproduction in previous rules, at the cost of removing the ability for universal computation and construction.[4]

Comparison of CA rulesets

CA number of states symmetries computation- and construction-universal size of self-reproducing machine
von Neumann 29 none yes 130,622 cells
Codd 8 rotations yes 283,126,588 cells[5]
Devore 8 rotations yes 94,794 cells
Banks-IV 4 rotations and reflections yes unknown
Langton's loops 8 rotations no 86 cells

Specification

Codd's CA has eight states determined by a von Neumann neighborhood with rotational symmetry.

The table below shows the signal-trains needed to accomplish different tasks. Some of the signal trains need to be separated by two blanks (state 1) on the wire to avoid interference, so the 'extend' signal-train used in the image at the top appears here as '70116011'.

purpose signal train
extend 70116011
extend_left 4011401150116011
extend_right 5011501140116011
retract 4011501160116011
retract_left 5011601160116011
retract_right 4011601160116011
mark 701160114011501170116011
erase 601170114011501160116011
sense 70117011
cap 40116011
inject_sheath 701150116011
inject_trigger 60117011701160116011

Universal computer-constructor

Codd designed a self-replicating computer in the cellular automaton, based on Wang's W-machine. However, the design was so colossal that it evaded implementation until 2009, when Tim Hutton constructed an explicit configuration.[5] There were some minor errors in Codd's design, so Hutton's implementation differs slightly, in both the configuration and the ruleset.

See also

References

  1. ↑ von Neumann, John; Burks, Arthur W. (1966). "Theory of Self-Reproducing Automata.". www.walenz.org. Archived from the original on 2008-01-05. Retrieved 2012-01-28.
  2. ↑ Codd, Edgar F. (1968). Cellular Automata. Academic Press, New York.
  3. ↑ Banks, Edwin (1971). Information Processing and Transmission in Cellular Automata. PhD thesis, MIT, Department of Mechanical Engineering.
  4. ↑ Langton, C. G. (1984). "Self-Reproduction in Cellular Automata". Physica D: Nonlinear Phenomena. 10 (1-2): 135–144. doi:10.1016/0167-2789(84)90256-2.
  5. 1 2 Hutton, Tim J. (2010). "Codd's self-replicating computer" (PDF). Artificial Life. 16 (2): 99–117. doi:10.1162/artl.2010.16.2.16200. PMID 20067401.

External links

This article is issued from Wikipedia - version of the 9/5/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.