Striking clock

The Elizabeth Tower of the Palace of Westminster in London, commonly referred to as Big Ben, is a famous striking clock.

A striking clock (also known as chiming clock) is a clock that sounds the hours audibly on a bell or gong. In 12-hour striking, used most commonly in striking clocks today, the clock strikes once at one a.m., twice at two a.m., continuing in this way up to twelve times at 12 noon, then starts again, striking once at one p.m., twice at two p.m., up to twelve times at 12 midnight.

The striking feature of clocks was originally more important than their clock faces; the earliest clocks struck the hours, but had no dials to enable the time to be read.[1] The development of mechanical clocks in Europe was motivated by the need to ring bells upon the canonical hours to call the community to prayer. The earliest known mechanical clocks were large striking clocks installed in towers in monasteries or public squares, so that their bells could be heard far away. Though an early striking clock in Syria was a 12-hour clock, many early clocks struck up to 24 strokes, particularly in Italy, where the 24-hour clock, keeping Italian hours, was widely used in the 14th and 15th centuries. As the modern 12-hour clock became more widespread, particularly in Great Britain and Northern Europe, 12-hour striking became more widespread and eventually became the standard. In addition to striking on the hour, many striking clocks play sequences of chimes on the quarter-hours. The most common sequence is Westminster Quarters.

Today the time-disseminating functions of clock striking are almost totally unnecessary, and striking clocks are kept for historical, traditional, and aesthetic reasons. Historic clock towers in towns, universities, and religious institutions worldwide still strike the hours, a famous example being Big Ben in London. Home striking clocks, such as mantel clocks, cuckoo clocks, and grandfather clocks are also common.

A typical striking clock will have two gear trains, because a striking clock must add a striking train that operates the mechanism that rings the bell in addition to the timekeeping train that measures the passage of time.

Passing strike

The Kremlin Clock on the Moscow Kremlin rings in 2012.

The most basic sort of striking clock simply sounds a bell once every hour. This sort of striking clock is called a passing strike clock. It is far simpler to create such a clock; all that must be done is to attach a cam to a shaft that rotates once an hour; the cam raises and then lets fall a hammer that strikes the bell. Originating before the mechanical clock itself, in water clocks, such clocks were the earliest striking clocks; they rang once for each canonical hour, and were used as reminders to summon monks or nuns to their prayers. This sort of striking is still found in some skeleton clocks. It does not require a separate gear train to arm and release the single stroke sounded.

The Tang Dynasty Chinese Buddhist monk and inventor Yi Xing (683727) created a rotating celestial globe that was given motive power by hydraulics of a turning waterwheel (acting as a large escapement), in the tradition of Zhang Heng (78139). This featured two wooden gear jacks on its horizon surface with a drum and a bell, the bell being struck automatically every hour and the drum being struck automatically every quarter-hour.[2] It is recorded that Confucian students in the year 730 were required to write an essay on this device in order to pass the Imperial examinations.[3] The use of clock jacks to sound the hours were used in later clock towers of Song Dynasty China, such as those designed by Zhang Sixun and Su Song in the 10th and 11th centuries, respectively.[4]

A striking clock outside of China was the clock tower near the Umayyad Mosque in Damascus, Syria, which struck once every hour. It was constructed by the Arab engineer al-Kaysarani in 1154. The Florentine writer Dante Alighieri made a reference to the gear works of striking clocks in 1319.[5] The most famous original striking clock tower still standing is possibly the one in St Mark's Clocktower in St Mark's Square, Venice. The St Mark's Clock was assembled in 1493, by the famous clockmaker Gian Carlo Rainieri from Reggio Emilia, where his father Gian Paolo Rainieri had already constructed another famous device in 1481. In 1497, Simone Campanato moulded the great bell (h. 1,56 m., diameter m. 1,27), which was put on the top of the tower where it's alternately beaten by the Due Mori (Two Moors), two bronze statues (h. 2,60) handling a hammer.

Counting the hours

During the great wave of tower clock building in 14th century Europe, around the time of the invention of the mechanical clock itself, striking clocks were built that struck the bell multiple times, to count out the hours. The clock of the Beata Vergine (later San Gottardo) in Milan, built around 1330, was one of the earliest recorded that struck the hours. In 1335, Galvano Fiamma wrote:[6]

There is there a wonderful clock, because there is a very large clapper which strikes a bell 24 times according to the 24 hours of the day and night, and thus at the first hour of the night gives one sound, at the second two strokes, and so distinguishes one hour from another, which is of greatest use to men of every degree.

The astronomical clock designed by Richard of Wallingford in 1327 and built around 1354, also struck 24 hours.

Some rare clocks use a form of striking known as "Roman Striking" invented by Joseph Knibb, in which a large bell or lower tone is sounded to represent "five", and a small bell or high tone is sounded to represent "one".[7] For example, four o'clock would be sounded as a high tone followed by a low tone, whereas the hour of eleven o'clock would be sounded by two low tones followed by a high tone. The purpose is to conserve the power of the striking train. For example, "VII" would be a total of three strikes instead of seven, and "XII" would be four strikes instead of twelve.[7] Clocks using this type of striking usually represent four o'clock on the dial with an "IV" rather than the more common "IIII",[7][8][9] so that the Roman numerals correspond with the sequence of strikes on the high and low bells.[7] One small table clock of this type sold from the George Daniels collection at Sotheby's on 6 November 2012 for £1,273,250.[10]


Countwheel striking: the unequally spaced notches in the countwheel (A) regulate the number of times the bell is struck.

Two mechanisms have been devised by clockmakers to enable striking clocks to correctly count out the hours. The earlier, which appeared in the first striking clocks in the 14th century, is called "countwheel striking". This uses a wheel that contains notches on its side, spaced by unequal, increasing arc segments. This countwheel governs the rotation of the striking train. When the striking train is released by the timekeeping train, a lever is lifted from a notch on the countwheel; the uneven notches allow the striking train to move only far enough to sound the correct number of times, after which the lever falls back into the next notch and stops the striking train from turning further.

The countwheel has the disadvantage of being entirely independent of the timekeeping train; if the striking train winds down, or for some other reason the clock fails to strike, the countwheel will become out of synch with the time shown by the hands, and must be resynchronized by manually releasing the striking train until it moves around to the correct position.

Rack striking

In the late seventeenth century, rack striking was invented. Rack striking is so called because it is regulated by a rack and snail mechanism. The distance a rack is allowed to fall is determined by a snail-shaped cam, thereby regulating the number of times the bell is allowed to sound. There was a misconception during the 20th century that the rack and snail mechanism was invented by British clergyman Edward Barlow in 1675-6.[1] In fact, the inventor is unknown.[11]

The snail-shaped cam is a part of the timekeeping train that revolves every twelve hours; often, the snail is attached to the center wheel that drives the hour hand of the clock. Like the countwheel, the cam stops the striking train when the appropriate count has been reached. The diameter of the cam is largest at the one o'clock position, permitting the rack to move only a short distance, after which the striking train is stopped; it is smallest at the 12 o'clock position, which allows the rack to move the farthest.

Because it is linked to the timekeeping train, rack striking seldom becomes desynchronized from the hands. Rack striking also made possible the repeating clock, which can be made to repeat the last hour struck by pressing a button. Rack striking became the standard mechanism used in striking clocks down to the present.[12]

Parts of mechanism

Rack striking: the snail-shaped cam (N) makes the clock sound the correct number of times by checking the fall of the rack (M).

All hour striking mechanisms have these parts.[13] The letters below refer to the diagram.

Clocks that have more elaborate functions than just striking the hours, such as chiming the quarter hours, or playing tunes, are called "chiming clocks" by clockmakers. The additional functions are usually run by a second complete striking mechanism separate from the (hour) striking train, called the "chiming train". These clocks have three weights or mainsprings, to power the timing train, striking train, and chiming train.

How it works

This describes how the rack and snail striking mechanism works. The labels refer to the drawing above.

The release lever (L) holds the rack (M) up when the clock is not striking. On the shaft of the minute hand (not shown), which rotates once per hour, there is a projection. As the change of the hour approaches, this projection slowly lifts the release lever, allowing the rack to fall until its point rests on the snail (N). The amount the rack can fall, and thus the number of strikes, is determined by the position of the snail. Exactly on the hour the striking train (G, H, K) is released and begins to turn. As it turns, the pins (G) repeatedly lift the hammer (F) and allow it to drop, ringing the gong (E). The gear ratios are arranged so that the gear wheel (H) makes one revolution each strike. A small pin (S) on this wheel engages the rack teeth, lifting the rack up by one tooth each turn. When the rack reaches the end of its teeth it stops the striking train from turning. So the number of strikes is equal to the number of teeth of the rack which are used, which depends on the position of the snail.

Types of striking clocks

A Cuckoo clock striking the 8th hour with mechanical automaton and the sound of a Cuckoo's call to mark the hours.

Specialized types of striking clocks:

Some quartz clocks also contain speakers and sound chips that electronically imitate the sounds of a chiming or striking clock. Other quartz striking clocks use electrical power to strike bells or gongs.


  1. 1 2 Milham 1945, p. 197.
  2. Needham 1986, pp. 473475.
  3. Needham 1986, p. 475.
  4. Needham 1986, p. 165.
  5. Needham 1986, p. 445.
  6. Boardman, Pete. "Why do clocks show 12 hours?". History. 24 Hour Clocks and Watches. Retrieved April 23, 2008.
  7. 1 2 3 4 Symonds 1947, p. 47.
  8. British Horological Institute, Workshop on Roman Numeral Clock Faces, 1999
  9. FAQ: Roman IIII vs. IV on Clock Dials
  10. "Sale L12313 The George Daniels Horological Collection" (PDF). Sotheby's.
  11. Horological Journal, September 2011, pages 408-412
  12. "Rack Striking". Encyclopedia of Antiques. Old and Sold Antique Marketplace. Retrieved 2008-04-20.
  13. Milham 1945, pp. 202204.

Sources and further reading

See also

This article is issued from Wikipedia - version of the 6/2/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.