Child safety seat

Child safety seat image indicating the various parts

Child safety seats (sometimes referred to as an infant safety seat, a child restraint system, a restraining car seat, or ambiguously as car seats) are seats designed specifically to protect children from injury or death during collisions. Car manufacturers may integrate child safety seats directly into their vehicle's design. Most commonly, these seats are purchased and installed by consumers. Many regions require children defined by age, weight, and/or height to use a government-approved child safety seat when riding in a vehicle. Child safety seats provide passive restraints and must be properly used to be effective. However, many child safety restraints in countries such as Canada and the United States are not used properly.[1] To tackle this negative trend, health officials and child safety experts produce child safety videos to teach proper car seat installation to parents and caregivers.

Baby car seats are legally required in many countries, including the United States, to safely transport children up to the age of 2 or more years in cars and other vehicles.

Other car seats, also known as "booster seats," are required until the child is large enough to use an adult seat belt. This is usually, but not always, when the child is 1.45m (4 ft 9 in) tall. The child needs to meet five criteria before moving out of the booster seat, including the child's seating position, shoulder belt position, lap belt position, knee position, and ability to sit properly for the length of the trip.

Generally, countries that regulate passenger safety have child safety laws that require a child to be restrained appropriately depending on their age and weight. These regulations and standards are often minimums, and with each graduation to the next kind of safety seat, there is a step down in the amount of protection a child has in a collision.[2] Some countries, such as Australia and the United States, forbid rear-facing child seats in a front seat that has an airbag. A rear-facing infant restraint put in the front seat of a vehicle places an infant's head close to the airbag, which can cause severe head injuries or death if the airbag deploys. Some modern cars include a switch to disable the front passenger airbag for child-supporting seat use.

In 2003, the American Academy of Pediatrics (AAP) suggested that infants “should spend minimal time in car seats (when not a passenger in a vehicle) or other seating that maintains supine positioning” to avoid developing positional plagiocephaly ("flat head syndrome").[3]

In 1990, the ISO standard ISOFIX[4] was launched in an attempt to provide a standard for fixing car seats into different makes of car. The standard now includes a top tether; the U.S. version of this system is called LATCH. Generally, the ISOFIX system can be used with Groups 0, 0+ and 1.

In 2013, a new car seat regulation was introduced: “i-Size” is the name of a new European safety regulation that affects car seats for children under 15 months of age. It came into effect in July 2013 and provides extra protection in several ways, most notably by providing rearward facing travel for children up to 15 months instead of 9 to 12 months, which the previous EU regulation advised.

History

Since the first car was manufactured and put on the market in the early 1900s, many modifications and adjustments have been implemented to protect those that drive and ride in motorized vehicles. Most restraints were put into place to protect adults without regard for young children. Though child seats were beginning to be manufactured in the early 1930s, their purpose was not the safety of children. The purpose was to act as booster seats to bring the child to a height easier for the driving parent to see them. It was not until 1962 that two designs with the purpose of protecting a child were developed independently.[5] British inventor Jean Ames created a rear-facing child seat with a Y-shaped strap similar to today's models.[6] American Leonard Rivkin, of Denver Colorado, designed a forward-facing seat with a metal frame to protect the child.[7] It is noted that seat belts for adults were not standard equipment in automobiles until the 1960s.

Classifications

Child safety seats

There are several types of car seats, which vary in the position of the child and size of the seat. The United Nations standard ECE R44/04[8] categorizes these into 4 groups: 0-3. Many car seats combine the larger groups 1, 2 and 3. Some new car models includes stock restraint seats by default.

Group 0

Infant Car Seat

Group 0 baby seats, or infant carriers, keep the baby locked up in a rear-facing position and are secured in place by a standard adult seat belt and/or an ISOFIX fitting.

Group 0 carrycots hold the baby lying on its back.

Carrycots are secured by both seat belts in the rear seat of the car. Both types have handles to allow them to be easily moved into and out of the car.

Fastened carrycots

Carrycots or infant car beds are used for children that cannot sit in a regular baby seat, such as premature infants or infants that suffer from apnea. A carrycot is a restraint system intended to accommodate and restrain the child in a supine or prone position with the child's spine perpendicular to the median longitudinal plane of the vehicle. Carrycots are designed to distribute the restraining forces over the child's head and body, excluding its limbs, in the event of a big crash. It must be put on the rear seat of the car. Some models can be changed to face forward after the baby has reached the weight limit which is normally about 15-20 kilograms.

Carrycots generally include a stomach belt and a connection to the (three points) safety belt.

Infant carriers

Rear-facing infant car seat

'Infant carrier' means a restraint system intended to accommodate the child in a rearward-facing semi-recumbent position. This design distributes the restraining forces over the child's head and body, excluding its limbs, in the event of the frontal collision.

For young infants, the seat used is an infant carrier with typical weight recommendations of 5-20 lb. Most infant seats made in the US can now be used up to at least 22 lb and 29 inches, with some going up to 35 lbs. In the past, most infant seats in the US went to 20 lb and 26 inches. Infant carriers are often also called "Bucket Seats" as they resemble a bucket with a handle. Some (but not all) seats can be used with the base secured, or with the carrier strapped in alone. Some seats do not have bases. Infant carriers are mounted rear-facing and are designed to "cocoon" against the back of the vehicle seat in the event of a collision, with the impact being absorbed in the outer shell of the restraint. Rear-facing seats are deemed the safest, and in the US children must remain in this position until they are at least 1 year of age and at least 20 pounds. although it is recommended to keep them rear-facing until at least 2 years old or until they outgrow the rear-facing car seat height and weight, whichever is longer.

Group 0+

Group O+ car seats commonly have a chassis permanently fixed into the car by an adult seat belt and can be placed into some form of baby transport using the integral handle if it is the specific model. Rear-facing child seats are inherently safer than forward-facing child seats because they provide more support for the child's head in the event of a sudden deceleration. Although some parents are eager to switch to a forward-facing child seat because it seems more "grown up," various countries and car seat manufacturers recommend that children continue to use a rear-facing child seat for as long as physically possible[9]

Convertible seats

Convertible Car Seat (Toddler)

Convertible seats can be used throughout many stages. Many convertible seats will transition from a rear-facing seat, to a forward-facing seat, and some then can be used as a booster seat. Many convertible seats allow for 5-40 lb. rear-facing, allowing children to be in the safer rear-facing position up to a weight of 40 pounds.

Convertible safety seats can be installed as either rear-facing or forward-facing. There is a large selection available to choose from and weight limits, height limits, and extra features vary from seat to seat and by manufacturer. Seats with a 5-point harness are considered safer than those with an overhead shield[10]

Convertibles aren't considered the best choice for a newborn because the bottom harness slots are often above the shoulders of most newborns. A seat with low bottom harness slots can be used if it is desired to use a convertible from birth.

Rear-facing weight limits range from 20 to 50 lb (9.1 to 22.7 kg) depending on the manufacturer and country of origin. Forward-facing limits range from 20 to 90 lb (9.1 to 40.8 kg) depending on the seat model and the manufacturer and country of origin.

Most convertible seats in the U.S. have at least a 35 lb rear-facing weight limit, most now to go to 40 lbs, some 45 and a few 50. The American Academy of Pediatrics (AAP) recommends that children remain rear-facing until they outgrow their convertible seat, regardless of how old they are. Children can remain in a rear-facing seat until they have either outgrown the weight limit for their seat, or the top of their head is within an inch of the top of the shell of the car seat.[11]

Group 1

A permanent fixture in the car using an adult seat belt to hold it in place and a five-point baby harness to hold the infant.

It is recommended that children sit rear-facing for as long as possible. In Scandinavian countries, for example, children sit rear-facing until around 4 years old. Rear-facing car seats are significantly safer in frontal collisions, which are the most likely to cause severe injury and death.[12][13][14][15][16][17][18][19][20][21][22] Rear-facing group 1 car seats are becoming more widespread but are still difficult to source in many countries.

Group 2

A larger seat than the Group 1 design. These seats use an adult seat belt to hold the child in place.

Group 3

Also known as booster seats, these position the child so that the adult seat belt is held in the correct position for safety and comfort.

Booster seats

Booster seats are recommended for children until they are big enough to properly use a seat belt. Seat belts are engineered for adults, and are thus too big for small children. In the United States, for children under the age of 4 and/or under 40 lb, a seat with a 5-point harness is suggested instead of a booster seat.[23]

Booster seats lift the child and allow the seat belt to sit firmly across the collar bone and chest, with the lap portion fitted to the hips. If the seat belt is not across the collar bone and the hips, it will ride across the neck and the stomach and cause internal injuries in the event of a collision.

There are two main types of boosters: high back (some of which have energy absorbing foam) and no back. A new generation of booster seats comes with rigid Isofix (Latch) connectors that secure to the vehicle's anchors, improving the seat's stability in the event of a collision.

The consumer group Which? is calling on manufacturers and retailers to phase out backless boosters, as it says they don't provide enough protection in side-impact crashes and could put children at risk.[24] So while backless booster cushions are better than using no child seat at all, they do not provide adequate protection in all circumstances.

Front-facing restraints

Used for Groups I, II and III.

After reaching one year of age and 20 lb, children may travel in forward-facing seats. Most Scandinavian countries require children to sit rear-facing until at least the age of 4 years. This has contributed to Sweden having the lowest rate of children killed in traffic in international comparisons.[25]

By law (in Canada and some US states), children need to be restrained until they are 4-years old and 40 lb. After the requirement is met, they can move into a booster seat.

Safety information

All child restraints have an expiration date. On average, most seats expire 6 years from the date of manufacture, although this can vary by manufacturer. Expiration dates are highly debated, with proponents and manufacturers claiming that older carseats can degrade over time to be less effective and that changing laws and regulations necessitate an expiration date. In addition, maintenance and parts are often not available for older models. Opponents argue that it is simply for their legal protection and to sell more carseats, and point out that manufacturers have noted that the plastics in most carseats long outlast the expiration date.

Like motorcycle and race car helmets, child restraints are tested for use in just one crash event. This means that if the restraint is compromised in any way (with or without the child in it), owners are strongly suggested to replace it. This is due to the uncertainty with how a compromised child restraint will perform in subsequent crashes.

The National Highway Traffic Safety Administration (NHTSA) provides guidance on the reuse of child restraint systems after a crash. Replacement of child restraints is recommended following a moderate or severe crash in order to ensure a continued high level of protection for child passengers. However, recent studies demonstrate that child restraints can withstand minor crash impacts without any documented degradation in subsequent performance.[26]

A minor crash is defined by the NHTSA as one in which all of the following apply:

Crashes that meet all of these criteria are much less severe than the dynamic testing requirement for compliance with Federal Motor Vehicle Safety Standard (FMVSS) 213 and are highly unlikely to affect future child safety seat performance.[26]

Child restraints are sometimes the subject of manufacturing recalls.[27] Recalls vary in severity; sometimes the manufacturer will send an additional part for the seat, other times they will provide an entirely new seat.

The purchase of a used seat is not recommended. Due to the aforementioned concerns regarding expiry dates, crash testing, and recalls, it is often impossible to determine the history of the child restraint when it is purchased second-hand.

Children traveling by plane are safer in a child safety seat than in a parent's arms. The FAA and the AAP recommend that all children under 40 lb use a child safety seat on a plane. Booster seats cannot be used on airplanes because they don't have shoulder belts.

Parents should not put children into safety seats with thick winter coats on. The coat will flatten in an accident and the straps will not be snug enough to keep the child safe.[28] An alternative would be placing a coat on the child backwards after buckling the child in.

Straps on the harness should be snug on the child, parents should not be able to pinch the straps away from the shoulders of the child. The straps also need to be placed at the proper height for the child.

Seat placement

A study of car crash data from 16 U.S. states found that children under the age of 3 were 43% less likely to be injured in a car crash if their car seat was fastened in the center of the back seat rather than on one side. Results were based on data from 4,790 car crashes involving children aged 3 and younger between 1998 and 2006. According to data, the center position was the safest but least used position. However, economist Steven Levitt (see below) has demonstrated that car seats do not reduce fatalities when compared to regular seat belts.[29]

The move from having car seats in the front passenger seat to having them in the back seat, facing backwards, may make it easier for a busy, distracted parent to forget an infant in the car.[30] Each year, between 30 and 50 infants die of heat illness and hypothermia in the United States after being left in a car.[30]

Law

Europe

Directive 2003/20/EC of the European Parliament and the Council[31] has mandated the use of child-restraint systems in vehicles effective May 5, 2006. Children less than 135 centimetres (53 in) tall in vehicles must be restrained by an approved child restraint system suitable for the child's size.[32] In practice, child restraint systems must be able to be fitted to the front, or other rows of seats. Children may not be transported using a rearward-facing child restraint system in a passenger seat protected by a front air bag, unless the air bag has been deactivated.

For a child restraint to be sold or used within any of the 56 UNECE member states it must be approved by the standards of UNECE Regulation 44/04, Directive 77/541/EEC or any other subsequent adaptation thereto. In order to be granted ECE R44 approval the child restraint must comply with several design, construction and production conformity standards.[33] If approval is granted the seat can display an orange label with the unique approval license number, the type of approval, the mass group approved for and the details of the manufacturer.

However, until May 9, 2008 member states may have permitted the use of child restraint systems approved in accordance with their national standards. EuroNCAP has developed a child-safety-protection rating to encourage improved designs. Points are awarded for universal child-restraint anchorages ISOFIX, the quality of warning labels and deactivation systems for front-passenger airbags.

2013: New EU I-Size regulation is introduced: “i-Size” is the name of a new European safety regulation, UNECE Regulation 129 that affects car seats for children under 15 months of age. It came into effect in July 2013 and provides extra protection in several ways, most notably by providing rearward facing travel for children up to 15 months instead of 9 to 12 months, which the previous EU regulation advised. Read more about I-Size. This new regulation is to be phased in between 2013 and 2018 and will be run in parallel to UNECE R44/04 until 2018 when it completely supersedes it.

Australia

AS1754

Australian laws regarding infants in motor vehicles were revised on November 9, 2009.

By law every child restraint sold in Australia must carry the Australian Standard AS/NZ1754 sticker (pictured right). Most overseas child restraints, including restraints from Europe and the USA, do not comply with these Standards and cannot legally be used in Australia. This also applies for ISOFIX child restraints imported from Europe or the USA.

In Australia there are six different types (Type A to Type F) of child restraints under the mandatory standard. Note: these restraints are NOT based on weight but on HEIGHT. All car seats with the AS/NZ1754 sticker will have height markers. These markers show clearly for what height the seat is appropriate.

The six types are:

  1. Type A: Rearward-facing or transversely installed restraint with a harness or other means of holding the child back
  2. Type B: Forward-facing chair with a harness
  3. Type C: Forward-facing harness without a chair
  4. Type D: Rearward-facing chair with harness
  5. Type E: a restraint that consists of either:
    • a booster seat or booster cushion used with a Type C child restraint and a seat belt, or with a lap-sash seat belt,
    • a converter seat suitable for children who weigh 18 to 32 kg.
  6. Type F: A restraint that consists of either:
    • a booster seat used in conjunction with a Type C child restraint and a seatbelt, or with a lap-sash seatbelt, suitable for children approximately 4 to 10 years of age, or
    • a converter used in conjunction with a seatbelt, suitable for children approximately 8 to 10 years of age.

Combination Type A/B: Child restraints can also be a combination of the above types. For example, a Type A/B converter seat.

The responsibility for children under the age of 16 using restraints or safety belts correctly rests with the driver. In Queensland, penalties for drivers not ensuring that passengers under the age of 16 are properly restrained involve a fine of A$300 and three demerit points. In Victoria the penalty is a fine of A$234 and three demerit points. Possible suspension or cancellation of license may also apply.

Exemptions to the law

Austria

Canada

Germany

Israel

The Israeli regulation states that a Sal Kal (he:סל קל lit. easy basket) is equal to European group 0 and group 0+ regulations [38]

An Urban legend [39] in Israel states that nursery homes and hospitals will not allow exit with an infant if a SalKal (infant carry one safety seat) is not presented.[40]

New Zealand

New Zealand Transport Agency governs the rules and sets standards for the health and safety aspects with respect to child restraints in New Zealand. Their guidelines dictate the minimum legal requirements for a New Zealand vehicle from the safety perspective. The correct fitting of a car seat can protect individuals and can be a life saver. This page provides details on qualified seat installation processes and approved standardized marks to look out for in child restraints. The Agency trains and certifies NZTA certified child restraint technicians who are authorized to install child safety seats.[41]

The New Zealand Transport Agency, as of March 16, 2012[42] stated that it is mandatory for the passengers to obey few below stated laws while travelling in a vehicle. These rules are regulations are set as per the age of the passengers. As of November 1, 2013, the rules are changing to mandate the use of approved child restraints for children aged 0–6. For children aged 7 a restraint must be used when it is available in the vehicle.[43]

Rules and regulations for different categories of age

[44]

Age group of children First Preference (recommended by law) Second Preference (To be followed if first preference cannot be sufficed) Third Preference Preference (minimal mandatory requirement by law if first/second preference cannot be sufficed)
Age 0–6 Use an approved child restraint
Seven years Use a child restraint Use a seat belt Travel seated at the back of the vehicle (if possible)
Eight to fourteen years Use a seat belt Travel seated at the back of the vehicle (if possible)
Fourteen years and above Use a seat belt (where fitted)

Children under 7 don't need to use an approved child restraint if:-

New Zealand Approved Marks for child restraints

All child restraints must meet the standards set by the New Zealand Transport Agency. There are different marks to indicate this approval from the safety perspective. Approved marks/symbols are shown in the table below:[45]

Symbol Description Standard followed
Tick Mark Australia and New Zealand standard - AS/NZ 1754
'E' mark and a number European Standard - ECE 44
'S' mark United States Standard - FMVSS 213

The number after 'E' in the ECE 44 standard indicates as to which country certifies the child restraint. Hence the number differs between countries. The EU (European Union) also has similar symbols to indicate safety standards for children travelling in a vehicle.

Spain

United Kingdom

From September 18, 2006, All children under the age of 12 have to use some form of child car seat, unless they are taller than 135 cm (4 ft 5in).[46][47]

United States

Manufacturing

Though there are hundreds of variations of makes and models in the world of child safety seats, the materials used in the manufacturing process are basically the same. Factories in which the seats are put together receive loads of polypropylene pellets.[49] Foam makes up the padding of the individual seats, while vinyl and fabrics are used to make up the covers for the seats as well as the harnesses.

A safety seat increases the safety of a properly restrained child in the case of a motor vehicle accident. The safety seat includes foam padding, fabric covers, a harness, and buckles or attaching mechanisms. Labels and instructions are also attached. Every child safety seat will have an expiration date on it. The Safe Kids USA organization does not recommend using a child safety seat that is more than 6 years old. Periodically, child safety seats are recalled by manufacturers for safety reasons. The National Highway Traffic Safety Administration posts a link to recent recall information at nhtsa.gov.

Types

Child safety seat

There are different types of child safety seats for children of different sizes and ages.

Some seats allow the child to stay rear-facing until 45 pounds (20 kg). Once the child has reached the minimum requirements to be forward facing, the seat can be turned around and used as a forward-facing seat.

Hazards

Manufacturers have quality controls to ensure seats are properly put together and packaged. However, it is not guaranteed that the included instructions are always adhered to and correctly followed. Up to 95% of the safety seats that are installed may not be the right seat for the child, may be hooked into the vehicle loosely, may be hooked with an incompatible belt in the vehicle, may have harnesses incorrectly fastened in some way, or may be incorrectly placed in front of air bags. In 1997, six out of ten children who were killed in vehicle crashes were not correctly restrained.[49]

Child Safety Seat Inspection site by the Maui Police Department

Along with the problem of instructions not being followed properly, there are other hazards that can affect children involving these safety seats. A recent study attributed many cases of sudden infant death syndrome (SIDS) to the prolonged sitting or lying position these infants are in when putting the safety seats to use. When researchers reviewed more than 500 infant deaths, it was found that 17 of these deaths occurred while the infant was in a device such as a child safety seat. The age of the most occurring rates of death by SIDS in a child safety device was found to be under one month, having six of the 17 deaths happen in this age group. Although SIDS has been found to be a high risk regarding child safety seats, a coroner in Quebec also stated that “putting infants in car seats…causes breathing problems and should be discouraged."[52] His warning came after the death of a two-month-old boy who was left to nap in a child safety seat positioned inside his crib rather than the crib itself. The death was linked to positional asphyxiation.[52] This means that the child was in a position causing him to slowly lose his supply of oxygen. Coroner Jacques Robinson said it's common for a baby's head to slump forward while in a car seat that is not properly installed in a car and that can diminish a baby's ability to take in oxygen. "The car seat is for the car," he said. "It's not for a bed or sleeping." Robinson added, however, he has nothing against car seats when they are properly used. <The Canadian Press, 2009> The coroner said that it is common for a baby’s head to “slump forward while in a car seat and that it diminishes oxygen”.[52]

The American Academy of Pediatrics says to “make sure the seat is at the correct angle so your infant’s head does not flop forward. Many seats have angle indicators or adjusters that can help prevent this. If your seat does not have an angle adjuster, tilt the car safety seat back by putting a rolled towel or other firm padding (such as a pool noodle) under the base near the point where the back and bottom of the vehicle seat meet.” Safety seats come with an instruction booklet with additional information on the appropriate angle for the seat.

Criticism

There has been some criticism of forward-facing child safety seats, in particular by the economist Steven D. Levitt, author of the popular book Freakonomics. In a 2005 article in the New York Times, Levitt suggests that the available data does not support the necessity of forward-facing child safety seats for children over two years old, arguing that the cheaper and simpler alternative of seat belts offers similar protection as forward-facing seats.[53] Levitt was a guest at the TED conference in the same year, and gave a lecture making the same case.[29] Levitt's study and findings have been criticized and refuted by subsequent peer reviewed studies, that found child safety seats offer a considerable safety advantage over seat belts alone.[54]

See also

Wikimedia Commons has media related to Infant automobile seats.

References

  1. "State of New Jersey". Nj.gov. Retrieved 2013-11-19.
  2. "Car Seats | Parents Central | Keeping Kids Safe". www.safercar.gov. Retrieved 2016-02-21.
  3. John Persing, MD, et al., American Academy of Pediatrics Committee on Practice and Ambulatory Medicine, Section on Plastic Surgery and Section on Neurological Surgery, "Prevention and Management of Positional Skull Deformities in Infants," Pediatrics 112, no. 1 (July 2003): 199-202.
  4. International Standard ISO 13216. Anchorages in vehicles and attachments to anchorages for child restraint systems. International Organization for Standardization, Geneva.
  5. "A Brief History of 7 Baby Basics". Mental Floss. 12 March 2013. Retrieved 26 December 2014.
  6. "Child Safety Seat". Made How. Retrieved 26 December 2014.
  7. United States Patent and Trademark Office. USPTO Full-Text and Image Database. Patent #3,107,942. Filed March 5, 1962 <http://patft.uspto.gov>.
  8. Regulation No 44 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of restraining devices for child occupants of power driven vehicles (‘child restraint systems’) - Retrieved 2014-08-04
  9. AAP UPDATES RECOMMENDATION ON CAR SEATS
  10. http://www.cpsafety.com/articles/fivepointshield.aspx
  11. Car Safety Seats
  12. Carlsson G, Norin H, Ysander L: Rearward-facing child seats – the safest car restraint for children? Accident Analysis and Prevention, 23(2-3):175-182, 1991.
  13. Kamrén B, von Koch M, Lie A, Tingvall C, Larsson S, Turbell T. The Protective Effect of Rearward Facing CRS. An Overview of possibilities and problems associated with child restraint for children aged 0-3 years. Child Occupant Protection symposium, San Antonio, November 1993. Society of Automotive engineers (SAE), Inc Warredale, PA. SAE technical paper 933093.
  14. Isaksson-Hellman I, Jakobson L, Gustafsson C, Norin H: Trends and effects of child restraint systems based on Volvo’s Swedish accident database. SAE Technical paper 973299. Society of Automotive Engineers (SAE). Warrendale, PA, 1997.
  15. Jacobsson L, Isaksson –Hellman I, Lundell B: Safety for the growing child – experiences from Swedish accident data. ESV conference 2005. Paper no 05-0330.
  16. Tingvall C. Children in cars. Doctor thesis. Some aspects of the safety of children as car passengers on road traffic accidents. Acta Paediatrica Scandinavica. Supplement, 339:1-35,1987. (Doctoral thesis)
  17. Turbell T. Child restraint systems: Frontal Impact Performance. VTI rapport 36A. Swedish Road and Traffic Research Institute (VTI) Stockholm Sweden. 1974.
  18. Fuchs S, Barthel MJ, Flannery, AM and Christoffel KK: Cervical spine fractures sustained by young children in forward facing car seats. Pediatrics 84(2), 348-354, 1989.
  19. Stalnaker RL: Spinal cord injuries to children in real world accidents. SAE SP-986. Society of Automotive Engineers (SAE). Warrendale, PA. 1993. Pp 173-183.
  20. Arbogast KB, Cornejo RA, Kallan MJ, Winston FK, Durbin DR: Injuries to children in forward facing child restraints. Association for the Advancement of Automotive Medicine 46th (AAAM). Annual Conference, Tempe, AX 2002. Pp 213-230.
  21. Henary B, Sherwood, C P, Crandall J R, Kent R W, Vaca F E, Arbogast K B, Bull M J. Car safety seats for children: rear facing for best protection. Injury Prevention 2007; 13:398-402.
  22. Sherwood C P, Crandall J R. Frontal sled tests comparing rear and forward facing child restraints with 1-3 year old dummies. Annual Proc Assoc Adv Automot Med. 2007;51:169-80.
  23. "Tips", CPS, US: NHTSA DoT, 2, archived from the original on May 15, 2008
  24. "Child safety week", Car safety & child seats, UK: Which, 2010, archived from the original on April 22, 2012
  25. http://www.anec.org/attachments/ANEC-PR-2008-PRL-007.pdf
  26. 1 2 "NHTSA Advises Parents, Caregivers: Child Safety Seats Can Be Reused after Minor Crash". National Highway Traffic Safety Administration. U.S. Department of Transportation. Retrieved 2 August 2016.  This article incorporates text from this source, which is in the public domain.
  27. http://www-odi.nhtsa.dot.gov/cars/problems/recalls/childseat.cfm
  28. "Winter coats and car seats: Keeping your child safe and warm". Consumer Reports. December 20, 2012. Retrieved 2013-09-19.
  29. 1 2 Lecture by Levitt at TED Retrieved June 2011
  30. 1 2 "The Last Word: Forgotten Baby Syndrome". The Week. March 26, 2009.
  31. Directive 2003/20/EC of the European Parliament and of the Council of 8 April 2003 amending Council Directive 91/671/EEC, Official Journal L 115 , 2003-05-09 P. 63.
  32. "European Commission Rules on Seat Belts". European Commission. European Commission. Retrieved 2 August 2016.
  33. http://www.childseatcentre.com/child-car-seat-regulations/
  34. RTA Child Restraints Regulations
  35. Impressum (2013-06-10). "ADAC Germany - Child restraint systems and booster seats". Adac.de. Retrieved 2013-11-19.
  36. http://www.rsa.gov.il/mianachnu/peilut/chakikashfita/Pages/hetkeneyRisun.aspx
  37. http://oldgov.gov.il/FirstGov/TopNav/Situations/SPopulationsGuides/SPSafeDriving/SPChildrenInCar/SPCDrivingChildren/
  38. http://oldgov.gov.il/FirstGov/TopNav/Situations/SPopulationsGuides/SPSafeDriving/SPChildrenInCar/SPCBabyYear/
  39. קניות לקראת לידה : תפוז, משפחה/הריון_ולידה_-_תמיכה , 01.12.2012
  40. regulations, Laniado Hospital
  41. Williams, Al (10 Oct 2013). "New child restraint rules near". stuff.co.nz. New Zealand. Retrieved 21 Feb 2016.
  42. "Using child restraints safely". NZ Transport Agency. Retrieved 23 July 2012.
  43. "Child restraint laws changing in New Zealand on November 1". drivingtests.co.nz. Retrieved 18 October 2013.
  44. "Child Restraint Law in New Zealand and Australia". Retrieved 28 July 2012.
  45. "How to tell if a child restraint is safe for New Zealand". NZ Transport Agency. Retrieved 28 July 2012.
  46. Q&A: New child car seat law
  47. Q&A: New child car seat law, BBC News, August 2006
  48. http://www.iihs.org/iihs/topics/laws/safetybeltuse?topicName=child-safety
  49. 1 2 AAP. "Car Safety Seats: A Guide For Families 2009." American Academy of Pediatrics. 2009. American Academy of Pediatrics. 22 Feb. 2009".
  50. NHTSA. "National Child Passenger Safety Certification Training Program Manual. Some combination seats must be converted to a booster after the child reaches 40 pounds (18 kg), while others have much higher weight limits for use of the 5-point harness (e.g., up to 85 pounds (39 kg)). Children are safest in a 5-point harness provided it is installed correctly and the child is within the height and weight limits for that particular seat." Safe Kids Worldwide, April 2007.
  51. NHTSA. "National Child Passenger Safety Certification Training Program Manual." Safe Kids Worldwide, April 2007.
  52. 1 2 3 “Child Safety Seat.” How Products Are Made. 2008. How It’s Made. 22 Feb. 2009 <http://www.madehow.com/Volume-5/Child-Safety-Seat.html>.
  53. Levitt, Steven D., The Seat Belt Solution, New York Times, July 10, 2005 Retrieved June 2011
  54. Elliot, Michael R. et. al. "Effectiveness of Child Safety Seats vs Seat Belts in Reducing Risk for Death in Children in Passenger Vehicle Crashes". JAMA Pediatrics. Retrieved 9 June 2015.
This article is issued from Wikipedia - version of the 11/3/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.