C mount

12 mm f/1.2 C-mount lens with a C-mount–to–CS-mount adapter

A C mount is a type of lens mount commonly found on 16 mm movie cameras, closed-circuit television cameras, machine vision cameras and microscope phototubes.

C-mount lenses provide a male thread, which mates with a female thread on the camera. The thread is nominally 1.000 inch (25.4 mm) in diameter, with 32 threads per inch, designated as "1-32 UN 2A" in the ANSI B1.1 standard for unified screw threads. The flange focal distance is 17.526 millimetres (0.6900 in) for a C mount.

Merely to say that a lens is "C-mount" says very little about the lens' intended use. C-mount lenses have been made for many different formats. C-mount lenses are built for the 8 mm and 16 mm film formats and the 1/3", 1/2", 2/3", 1", and 4/3" video formats, which corresponds to a range of image circles approximately from 5 to 22 mm in diameter.

Depending on the format, the design of the lens and its performance will differ considerably. For example, for the 4/3 format, a 12 mm lens is a wide-angle lens and will have a retrofocus design. For the 2/3-inch format, a 12 mm lens is "normal" and can have a simple and fast double Gauss layout. For the 1/3-inch format, a 12 mm lens is long and can have a telephoto design.

Some TV lenses lack provision to focus or vary the aperture, so may not operate properly with film cameras. Also, some TV lenses may have bits that protrude behind the mount far enough to interfere with the shutter or reflex finder mechanisms of a film camera.

Although C-mount lenses have a back focal distance far too short to be used with 35 mm film SLRs or any existing digital SLR, they can be mounted on interchangeable-lens mirrorless digital cameras. One such system is the Micro Four Thirds, being used by Olympus and Panasonic. However, the vast majority of C-mount lenses produce an image circle too small to effectively cover the entire (micro-)four-thirds sensor, with has approximately 22 mm diagonal. This produces what is popularly called vignetting but is better described as a mismatch between camera format and lens format.[1]

C mount was created by Bell & Howell for their Filmo 70 cine cameras.[2] The earliest Filmos had a slightly different mounts, known as A mount, and B mount. C mount was found on Filmo 70 cameras with serial numbers 54090 and higher,[3] probably from about 1926. Soon after, other camera manufacturers adopted the same mount, and it became a de facto standard for 16 mm cine cameras.

CS mount

CS-mount has a flange focal distance of 12.50 millimetres (0.492 in), but is otherwise the same as C-mount, including the fact that lenses for many different formats are made for it. CS-mount lenses are built for the smaller formats, 1/2 inch and down.

Combinations: C, CS and extension adapter
Camera
body
Extension
tube
adapter
Lens Net
effect
Focus View
angle
Zoom Exposure
C C Normal Normal Normal Normal
C CS +5 mm Near-sighted Narrower Larger Darker
C 5.0 mm (0.20 in) C +5 mm Near-sighted Narrower Larger Darker
C 5.0 mm (0.20 in) CS +10 mm Most near-sighted Narrowest Largest Darkest
CS C −5 mm Far-sighted Wider Smaller Brighter
CS CS Normal Normal Normal Normal
CS 5.0 mm (0.20 in) C Normal Normal Normal Normal
CS 5.0 mm (0.20 in) CS +5 mm Near-sighted Narrower Larger Darker

See also

References

  1. Lawrenceripsher.com: Switar 26mm f/1.1 Review Archived December 15, 2009, at the Wayback Machine..
  2. Yahoo Group discussion: Cine Camera Collectors
  3. Kodak Movie News, Vol. 2, No. 3 (May–June 1954).

External links

This article is issued from Wikipedia - version of the 11/14/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.