Balun

For the village in Iran, see Balun, Iran.
Pair of AC&E 120 Ω twisted pair (Krone IDC) to 75 Ω coaxial cable balun transformers. Actual length is about 3cm.

A balun /ˈbælʌn/ is an electrical device that converts between a balanced signal (two signals working against each other where ground is irrelevant) and an unbalanced signal (a single signal working against ground or pseudo-ground). A balun can take many forms and may include devices that also transform impedances but need not do so. Transformer baluns can also be used to connect lines of differing impedance. Sometimes, in the case of transformer baluns, they use magnetic coupling but need not do so. Common-mode chokes are also used as baluns and work by eliminating, rather than ignoring, common mode signals.

The origin of the word balun is “balanced to unbalanced”.

A variation of this device is the UNUN, which transfers signal from one unbalanced line to another.

Types of balun

Classical transformer type

Isolation transformer

In classical transformers, there are two electrically separate windings of wire coils around the transformer’s core. The advantage of transformer-type over other types is that the electrically separate windings for input and output allow these baluns to connect circuits whose ground-level voltages are subject to ground loops or otherwise electrically incompatible; for that reason they are often called isolation transformers.

This type is sometimes called a “voltage balun”. The ‘primary’ winding receives the input signal, and the ‘secondary’ winding puts out the converted signal. The core that they are wound on may either be empty (an “air core”) or equivalently a magnetically neutral material like a porcelain support, or it may be a material which is good magnetic conductor like ferrite in modern "high-frequency" (HF) baluns, or of ‘soft iron’ as in the early days of telegraphy.

The electrical signal in the primary coil is converted into a magnetic field in the transformer’s core. When the electrical current through the primary reverses, it causes the established magnetic field to collapse. The collapsing magnetic field then induces an electric field in the secondary winding.

The ratio of loops in each winding and the efficiency of the coils’ magnetic coupling determines the ratio of electrical potential (Voltage) to electrical current (Amperage) and the total power of the output. For idealized transformers, although the ratio of Voltage to Amperage will change in exact proportion to the square of the winding ratio, the power (measured in Watts) remains identical. In real transformers, some energy is lost inside due to heating of the metallic core of the transformer, and lost outside to the surrounding environment due to imperfect magnetic coupling between the two coils.

Autotransformer type

Circuit diagram of a 4:1 autotransformer balun using three taps on a single winding on a ferrite rod.

Generally a balun consists of two wires (primary and secondary) and a toroid core: it converts the electrical energy of the primary wire into a magnetic field. Depending on how the secondary wire is done, the magnetic field is converted back to an electric field. An autotransformer balun has only one coil, or is made of two or more coils that have an electrical connection. The coil is typically wound on a ferrite rod or doughnut-shaped toroid. One can also make an autotransformer from an ordinary transformer by cross-wiring the primary and secondary windings. Baluns made with autotransformer windings are also called “Voltage baluns”, since they produce balanced output voltage, but not necessarily balanced current.

Picture a 4:1 balun of the same design, wound on ferrite toroid. Notice that the black and red winding wires are joined at the threaded connector.

In all autotransformers, the single winding must have at least one extra electrical connection – called a tap or tap point – between the two ends of the winding. The current sent into the balun through one pair of connections acts as if it were a primary coil, and magnetizes the entire core. When the electric current in the input segment of the coil changes, the induced magnetic field collapses and the collapse of the magnetic field in the core induces an electric current in the entire coil. Electrical connections to parts of the coil different from the input connections have higher or lower voltages depending on the length of the coil that the output is tapped from.

As with a two-winding transformer balun, the ratio of voltage to current changes in proportion to the square of number of windings between the two input wires divided by the number of windings between the two output wires.

Unlike transformer-type baluns, autotransformer baluns connect all the wires connected to them to a single ground voltage level. Since outdoor antennas are prone build-up of static electric charge, the path for the static to drain to ground through an autotransformer balun can be a distinct advantage.

Transmission-line transformer type

Transmission line or “choke” baluns can be considered as simple forms of transmission line transformers. This type is sometimes called a “current balun”, since it ensures equal current on both sides of its output, but not necessarily equal voltage.

Homemade 1:1 balun using a toroidal core and coaxial cable. This simple RF choke works as a balun by preventing signals passing along the outside of the braid. Such a device can be used to cure television interference by acting as a braid-breaker.

A more subtle type results when the transformer type (magnetic coupling) is combined with the transmission line type (electro-magnetic coupling). Most typically the same kind of transmission line wires are used for the windings as carry the signal from the radio to the antenna, although these baluns can be made using any type of wire. The resulting devices have very wideband operation.[1] "Transmission line transformers" commonly use small ferrite cores in toroidal "rings" or two-hole "binocular" shapes. Something as simple as 10 turns of coaxial cable coiled up on a diameter about the size of a dinner plate makes an effective choke balun for frequencies from about 10 MHz to beyond 30 MHz. The magnetic material may be "air", but it is a transmission line transformer.

The Guanella transmission line transformer (Guanella 1944) is often combined with a balun to act as an impedance matching transformer. Putting balancing aside a 1:4 transformer of this type consists of a 75 Ω transmission line divided in parallel into two 150 Ω cables, which are then combined in series for 300 Ω. It is implemented as a specific wiring around the ferrite core of the balun.

Delay line type

A large class of baluns uses connected transmission lines of specific lengths, with no obvious "transformer" part. These are usually built for (narrow) frequency ranges where the lengths involved are some multiple of a quarter wavelength of the intended frequency in the transmission line medium. A common application is in making a coaxial connection to a balanced antenna, and designs include many types involving coaxial loops and variously connected "stubs".

One easy way to make a balun is a one-half wavelength (λ/2) length of coaxial cable. The inner core of the cable is linked at each end to one of the balanced connections for a feeder or dipole. One of these terminals should be connected to the inner core of the coaxial feeder. All three braids should be connected. This then forms a 4:1 balun which works at only one frequency.

Another narrow band design is to use a λ/4 length of metal pipe. The coaxial cable is placed inside the pipe; at one end the braid is wired to the pipe while at the other end no connection is made to the pipe. The balanced end of this balun is at the end where no connection is made to the pipe. The λ/4 conductor acts as a transformer, converting the zero impedance at the short to the braid into an infinite impedance at the open end. This infinite impedance at the open end of the pipe prevents current flowing into the outer coax formed by the outside of the inner coax shield and the pipe, forcing the current to remain in the inside coax. This balun design is not good for low frequencies because of the long length of pipe that will be needed. An easy way to make such a balun is to paint the outside of the coax with conductive paint, then to connect this paint to the braid through a break in the outer insulation 1/4 wave from the end. For both forms (pipe or paint), the length is dependent on the velocity factor for the outer transmission line.

Self resonance

Although baluns are designed as magnetic devices – each winding in a balun is an inductor – all transformers made of real materials also have a small capacitance between the primary and secondary windings, as well as between individual loops in any single winding. This unwanted capacitance is called “self-capacitance”.

The electrical connection of capacitance and inductance leads to a frequency where Electrical reactance of the self-inductance and self-capacitance in the balun are equal and opposite: resonance. A balun of any design operates poorly at frequencies at or above its resonance, and some of the design considerations for baluns are for the purpose of making the resonant frequency as far above the operating frequency as possible.

Balun alternatives

An RF choke can be used in place of a balun. If a coil is made using coaxial cable near to the feed point of a balanced antenna, then the RF current that flows on the outer surface of the coaxial cable can be attenuated. One way of doing this would be to pass the cable through a ferrite toroid.(Straw 2005, 25-26)

Applications

A balun's function is generally to achieve compatibility between systems, and as such, finds extensive application in modern communications, particularly in realising frequency conversion mixers to make cellular phone and data transmission networks possible. They are also used to convert an E1 carrier signal from coaxial cable (BNC connector,1.0/2.3 connector,1.6/5.6 connector,Type43 connectors) to UTP CAT-5 cable or IDC connector.

Radio and television

A 75-to-300 Ω balun built into the antenna plug.

In television, amateur radio, and other antenna installations and connections, baluns convert between impedances and symmetry of feedlines and antennas.[2] For example, transformation of 300 Ω twin-lead or 450 Ω ladder line (balanced) and 75 Ω coaxial cable (unbalanced), or to directly connect a balanced antenna to unbalanced coaxial cable. To avoid feed line radiation, baluns are typically used as a form of common mode choke attached at the antenna feed point to prevent the coaxial cable from acting as an antenna and radiating power. This typically is needed when a balanced antenna (for instance, a dipole) is fed with coax; without a balun, the shield of the coax could couple with one side of the dipole, inducing common mode current, and becoming part of the antenna and unintentionally radiating.[3]

When it comes to transmitting antennas the choice of the toroid core is crucial. A rule of thumb is: the more power the bigger the core.[4]

In measuring the impedance or radiation pattern of a balanced antenna using a coaxial cable, it is important to place a balun between the cable and the antenna feed. Unbalanced currents that may otherwise flow on the cable will make the measured antenna impedance sensitive to the configuration of the feed cable, and the radiation pattern of small antennas may be distorted by radiation from the cable.

Baluns are present in radars, transmitters, satellites, in every telephone network, and probably in most wireless network modem/routers used in homes. It can be combined with transimpedance amplifiers to compose high-voltage amplifiers out of low-voltage components.

Video

Baseband video uses frequencies up to several megahertz. A balun can be used to couple video signals to twisted-pair cables instead of using coaxial cable. Many security cameras now have both a balanced unshielded twisted pair (UTP) output and an unbalanced coaxial one via an internal balun. A balun is also used on the video recorder end to convert back from the 100 Ω balanced to 75 Ω unbalanced. A balun of this type has a BNC connector with two screw terminals. VGA/DVI baluns are baluns with electronic circuitry used to connect VGA/DVI sources (laptop, DVD, etc.) to VGA/DVI display devices over long runs of CAT-5/CAT-6 cable. Runs over 130 m (400 ft) may lose quality due to attenuation and variations in the arrival time of each signal. A skew control and special low skew or skew free cable is used for runs over 130 m (400 ft).

Audio

Three audio transformers, two of them baluns

In audio applications, baluns convert between high impedance (see Nominal impedance) unbalanced and low impedance balanced lines. Another application is decoupling of devices (avoidance of earth loops).

A third application of baluns in audio systems is in the provision of balanced mains power to the equipment. Due to the common-mode rejection of interference characteristic of balanced mains power, a wide range of noise coming from the wall plug is eliminated, e.g. mains-borne interference from air conditioner/furnace/refrigerator motors, switching noise produced by fluorescent lighting and dimmer switches, digital noise from personal computers, and radio frequency signals picked up by the power lines/cords acting as antennae. This noise infiltrates the audio/video system through the power supplies and raises the noise floor of the entire system.[5]

Except for the connections, the three devices in the image are electrically identical, but only the leftmost two can be used as baluns. The device on the left would normally be used to connect a high impedance source, such as a guitar, into a balanced microphone input, serving as a passive DI unit. The one in the centre is for connecting a low impedance balanced source, such as a microphone, into a guitar amplifier. The one at the right is not a balun, as it provides only impedance matching.

Other applications

See also

References

  1. Sevick 1990, pp. 1-1
  2. Baluns: What They Do And How They Do It (W7EL) http://www.eznec.com/Amateur/Articles/Baluns.pdf
  3. Feeding a Dipole Antenna with a Balun
  4. Toroid Cores for 1:4 Baluns (DG3OBK) http://www.aroesner.homepage.t-online.de/balun.html
  5. Balanced Power Technologies http://www.b-p-t.com/
  • Guanella, G. "New method of impedance matching in radio-frequency circuits." Brown Boveri Review, September 1944: 329329.
  • Sevick, Jerry (W2FMI). Transmission Line Transformer, The American Radio Relay League, 1990, ISBN 0-87259-296-0.
  • Sevick, Jerry (W2FMI). Building and Using Baluns and Ununs: Practical Designs for the Experimenter. 1994.
  • Radio communication handbook, 5th ed. (Radio Society of Great Britain, 1976) 12.41, 13.5.
  • Straw, R. Dean. ARRL Antenna Book. 20th ed. (Newington, CT: American Radio Relay League, 2005) ISBN 0-87259-904-3.
This article is issued from Wikipedia - version of the 11/4/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.